Results 91 to 100 of about 131,482 (265)

RETRACTED: Design and Hydrodynamic Performance Analysis of Airlift Sediment Removal Equipment for Seedling Fish Tanks

Journal of Marine Science and Engineering
This study innovatively proposes a pipeline-type pneumatic lift sediment removal device for cleaning pollutants at the bottom of fish breeding tanks and conducts hydrodynamic characteristic analysis on its core component, the pneumatic lift pipeline ...
Yufei Zhang, Andong Liu, Chenglin Zhang, Chongwu Guan, Haigeng Zhang   +4 more
doaj   +1 more source

Solid Particle‐Liquid Metal Mixtures for Robust High‐Current Interconnects in Stretchable Electronics and Soft Robotics

Advanced Materials Technologies, EarlyView.
Metallic microparticles dispersed in liquid metal interconnects mitigate electromigration‐induced failure by reconfiguring internal current density distributions. These fillers facilitate the growth of a robust, protective gallium oxide shell at elevated temperatures, shifting the failure threshold toward a thermal limit.
Ethan J. Krings, Calan Brant, Carson Emeigh, Donovan Vincent Jr., Ravi Tutika, Sangjin Ryu, Eric J. Markvicka   +6 more
wiley   +1 more source

Numerical analysis of thermal performance of various types of horizontal ground heat exchangers

AIP Advances
In this paper, three types of horizontal ground heat exchangers (GHEs) such as U-tube, spiral, and slinky were numerically analyzed to investigate their thermal performance in cooling mode for 7 days of continuous operation with specific boundary ...
Nushrat Jahan, Md Hasan Ali, Akio Miyara
doaj   +1 more source

A Direction‐Aware Piezo‐Transmittance Strain Sensor via Engineered Alignment of Carbon Nanotubes (CNTs)

Advanced Materials Technologies, EarlyView.
A direction‐aware piezo‐transmittance strain sensor is realized through the engineered alignment of carbon nanotubes. This anisotropic architecture instantaneously modulates optical transmittance, achieving ultra‐high sensitivity and exceptionally low hysteresis. By effectively eliminating signal crosstalk to precisely decouple multidirectional strains,
Byeongmin Kang, Kwangjun Kim, Jimin Gu, Junseong Ahn, Yongrok Jeong, Ji‐Hwan Ha, Sohee Jeon, Soonhyoung Hwang, Byung‐Ho Kang, Jihyeon Ahn, Jong‐An Choi, Minwook Kim, Yeonguk Jung, Jun‐Ho Jeong, Jong G. Ok, Inkyu Park   +15 more
wiley   +1 more source

Study on Flow Characteristics of Venturi Accelerated Vortex Drainage Tool in Horizontal Gas Well

Applied Sciences
Vortex drainage gas recovery has been used to carry liquid from gas wells. However, the traditional vortex tools in gas wells cannot produce long effective distance spiral flow at a low gas flow rate, and their operating mechanism has not been thoroughly
Hongtao Zhang, Yan Xu, Meng Cai, Junliang Li, Mingxi Feng, Xiaochuan Zhang   +5 more
doaj   +1 more source

Fabrication of Fibers With Complex Features Using Thermal Drawing of 3D‐Printed Preforms

Advanced Materials Technologies, EarlyView.
3D printing enables rapid fabrication of macroscale polymer preforms with complex geometries. Thermal drawing then scales these structures into long fibers while preserving micron‐scale cross‐sectional features. This workflow provides a fast, low‐cost route to functional fibers with tailored geometries and material combinations for catheter, robotic ...
Ali Anil Demircali, Jinshi Zhao, Ayhan Aktas, Mohamed E. M. K. Abdelaziz, Burak Temelkuran   +4 more
wiley   +1 more source

Wood‐Derived Nanocellulose‐Biocarbon Fresnel‐Zone Plate Lenses for Sub‐THz Frequency Applications

Advanced Materials Technologies, EarlyView.
Wood‐derived nanocellulose and lignin‐based biocarbon were combined to fabricate fully bio‐based Fresnel zone plate (FZP) lenses for sub‐terahertz frequencies. These sustainable FZP lenses exhibit low dielectric loss and high directivity, achieving performance comparable to that of metallic references, and remain functional under environmental stress ...
Riikka Haataja, Mikko Kokkonen, Niina Halonen, Sami Myllymäki, Umair Rafique, Mandeep Singh, Ossi Laitinen, Heli Jantunen, Kristiina Oksman, Henrikki Liimatainen   +9 more
wiley   +1 more source

Deterministic Integration of Quantum Emitters and Optical Cavities in a Van Der Waals Crystal

Advanced Optical Materials, EarlyView.
The work demonstrates fabrication of Circular Bragg Grating (CBG) cavities with embedded emitters in hBN. The cavities are fabricated around a pre‐characterised quantum emitter. The integrated platform enables light matter interaction and access to brighter emitters and spins in hBN.
James Liddle‐Wesolowski, Otto Cranwell Schaeper, Nathan Coste, Benjamin Whitefield, Evan Williams, Helen Zhi Jie Zeng, Mehran Kianinia, Anastasiia Zalogina, Igor Aharonovich   +8 more
wiley   +1 more source

Experimental Studies on Flow Boiling of R134a in Horizontal Small Tubes

Zhileng xuebao, 2015
Experimental investigation on the flow boiling of R134a in horizontal mini-channels was carried out in this study. The test sections are three different horizontal smooth stainless steel tubes with inner diameter of 1mm, 2mm and 3mm.
Ding Yang, Liu Jianhua, Ye Fangping, Jiang Linlin, E Xiaoxue, Wu Hao   +5 more
doaj  

Harnessing Ultrafast Optical Pulses for 3D Microfabrication by Selective Tweezing and Immobilization of Colloidal Particles in an Integrated System

Advanced Photonics Research, Volume 6, Issue 5, May 2025.
Microfabrication using nano‐ to micron‐sized blocks has transformative potential for next‐gen electronics, optoelectronics, and materials. Traditional methods are limited by scalability and precision. STIC, a single‐laser system for precise colloid manipulation and immobilization using femtosecond lasers, is introduced that enables efficient 3D ...
Krishangi Krishna, Jieliyue Sun, Wenyu Liu, Robert H. Hurt, Kimani C. Toussaint Jr.   +4 more
wiley   +1 more source