Results 101 to 110 of about 46,528 (305)
Counterion Dependent Side‐Chain Relaxation Stiffens a Chemically Doped Thienothiophene Copolymer
Advanced Functional Materials, EarlyView.Oxidation of a thienothiophene copolymer, p(g3TT‐T2), via different doping strategies and dopant molecules resulted in materials with similar oxidation levels and a high electrical conductivity of ≈100 S cm−1. However, mechanical properties varied significantly, with sub‐glass transition temperatures and elastic moduli spanning from –44°C to –3°C and ...
Mariavittoria Craighero +12 more
wiley +1 more source
, 2011 Objective: To determine the effects of the simultaneous application of contrast temperature therapy with intermittent compression as a recovery strategy for the quadriceps muscle following exercise induced muscle damage in moderately active adult ...
Holroyd, Wayne
core
, 2021 Hot deformation behavior and the microstructural evolution of Inconel 625 superalloy plates are investigated by hot compression tests in a range of working temperatures (800–1050 °C) and strain rates (0.001–1 s−1).
Bin Tang +5 more
core +1 more source
Receptor‐Free Identification of Toxic Gases Enabled by Hygroscopic Aqueous Salt Films
Advanced Functional Materials, EarlyView.Water as a gas sensor coating sounds impossible—until it stops evaporating. Here, hygroscopic salt solutions (LiCl, LiBr, H3PO4) form non‐drying aqueous films on CNT chemiresistors under ambient air. Gases partition into these liquid layers, sometimes transforming into water, and generate salt‐specific resistance fingerprints across a four‐channel ...
Seongwoo Lee +5 more
wiley +1 more source
Dynamic Recrystallization during Hot Compression Processes of 304 Austenite Stainless Steel
, 2010 Hot compression experiments of 304 austenite stainless steel were carried out with Gleeble-1500D simulator under the strain rates of 0.05 s-1~0.5 s-1 at 950°C~1200°C.
Jian Sheng Liu +3 more
core +1 more source
EVALUATING HOT DEFORMATION BEHAVIOR OF W360 TOOL STEEL BY HOT COMPRESSION TEST
Journal of Advanced Materials in Engineering, 2021 In this research, the hot deformation behavior of W360 tool steel was investigated using hot compression test at 1000-1200°C and strain rates of 0.001, 0.01, 0.1, and 1 s-1. According to the results, dynamic recrystallization was found the most important
R. Amirarsalani +2 more
doaj
Advanced Functional Materials, EarlyView.A soft, dual‐channel hydrogel patch enables simultaneous detection of wound temperature and strain by integrating ion‐diffusion‐mediated thermoelectric and resistive sensing. The conformal design maintains stable performance during motion, capturing subtle inflammatory and mechanical changes for continuous wound monitoring.
Yu Fang +7 more
wiley +1 more source
Evaluation of Friction Properties of Magnesium Alloy during Hot Forging by Ring Compression Test
, 2017 This paper deals with friction properties and deformation resistance during hot forming of Mg-Al-Ca-Mn series magnesium alloys. Friction coefficients between dies and magnesium alloys were obtained by ring compression tests that used graphite, PTFE, and ...
Hisaki Watari +4 more
core +1 more source
Microstructure Evolution of the Ti-46Al-8Nb-2.5V Alloy during Hot Compression and Subsequent Annealing at 900 °C. [PDF]
Materials (Basel), 2023 Cao S, Li Z, Pu J, Han J, Dong Q, Zhu M.
europepmc +1 more source
Advanced Functional Materials, EarlyView.A compostable PGS soft surgical robot with interchangeable modules integrates transient Mo tactile and Si thermal sensors for dual feedback. The device preserves its function after clinical‐grade sterilization, demonstrates stable actuation and cardiac tissue grasping with real‐time in vivo pulsatile monitoring, and biodegrades post‐use with soil‐safe,
Minseong Chae +27 more
wiley +1 more source