Results 91 to 100 of about 46,528 (305)
Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions
Advanced Engineering Materials, EarlyView.This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi +5 more
wiley +1 more source
, 2007 : The present work describes a hybrid modelling approach developed for predicting the flow behaviour, recrystallisation characteristics and crystallographic texture evolution in a Fe-30wt%Ni austenitic model alloy subjected to hot plane strain ...
Sellars, CM +4 more
core
Finite element analysis of small-scale hot compression testing
, 2022 This paper models hot compression testing using a dilatometer in loading mode. These small-scale tests provide a high throughput at low cost, but are susceptible to inhomogeneity due to friction and temperature gradients.
core +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Microstructural evolution of AISI304 stainless steel in the Steckel Mill rolling process
, 2004 Includes bibliographical references (leaves [105]-110).The microstructural evolution of AISI304 stainless steel in the Steckel mill rolling process is investigated.
Parker, Sa-aadat
core
Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition
Advanced Engineering Materials, EarlyView.AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley +1 more source
Microstructure Evolution of 1235 Aluminum Alloy after Hot Compression Deformation
, 2011 Microstructure evolution behavior of 1235 aluminum alloy under different deformation conditions was studied by hot compression simulation, along with OM, TEM. The law of microstructure evolution at hot deformation was also analyzed.
Gui Qing Chen +4 more
core +1 more source
A Study on Thermal Compression Deformation and Structure of 700 MPa Pipeline Steel
Teshugang, 2018 With using Gleeble-3500 thermal simulator the single pass hot compression deformation and structure evolution of 20 mm hot-rolled plate of 700 MPa pipeline steel (/%: 0.07C, 0.90Si, 0.60Mn, 0.008P, 0.002S, 0.30Ni, 0.10Cr, 0.12Mo, 0.06V, 0.03Nb, 0.28Cu, 0.
杨秀芝 +4 more
doaj
Hot‐Film and Calorimetric Methods With Transient Heating for Measurement of High Biofluid Flow Rate
Advanced Functional Materials, EarlyView.Accurate measurement of biofluid flow rate is vital for clinical diagnostics. We propose a transient heating strategy using short thermal pulses and peak temperature tracking to enhance the flow sensitivity of the hot‐Film and calorimetric methods. Simulations show how optimal heating time maximizes sensitivity across flow rates.
Yuanting Wei +8 more
wiley +1 more source
The Portevin-Le Chatelier Effect of Cu-2.0Be Alloy during Hot Compression. [PDF]
Materials (Basel), 2023 Zhu D +8 more
europepmc +1 more source