Results 1 to 10 of about 226,190 (309)

Room temperature deformation mechanisms of a Fe–Mn–Al–C steel

Journal of Materials Research and Technology, 2023
This study aims to investigate the deformation mechanisms of an austenite-based duplex Fe–Mn–Al–C steel at room-temperature through uniaxial tensile tests, strain rate sensitivity and stress relaxation analysis.
A. Moshiri, A. Zarei-Hanzaki, J. Charkhchian, A.S. Anousheh, R. Khani, H.R. Abedi   +5 more
doaj   +1 more source

On the cyclic deformation behavior and correlated damage mechanism of selective laser melted AlSi10Mg alloy holding different initial microstructures

Journal of Materials Research and Technology, 2023
The present work deals with the cyclic deformation behavior of AlSi10Mg alloy fabricated through selective laser melting. Toward this end, the printed material was heat treated and was tested through strain-controlled push–pull fatigue under different ...
F. Bathaee, A. Zarei-Hanzaki, A. Moshiri, H.R. Abedi   +3 more
doaj   +1 more source

Improved strength and plasticity of magnesium matrix nanocomposites reinforced by carbonaceous nanoplatelets and micro-clusters

Journal of Materials Research and Technology, 2022
The uniform distribution of carbonaceous nanomaterials in a magnesium matrix composite can dramatically improve the strength without sacrificing ductility.
M. Tahaghoghi, A. Zarei-Hanzaki, M.S. Jalali, H.R. Abedi   +3 more
doaj   +1 more source

The effect of heat treatment on the room and high temperature mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

Journal of Materials Research and Technology, 2023
The present work demonstrates a novel interpretation of the effect of well-known heat treatments of solutionizing (ST) and solutionizing plus aging (T6) along with a newly-developed direct aging (DA), on the microstructural evolution and corresponding ...
N. Tabatabaei, A. Zarei-Hanzaki, A. Moshiri, H.R. Abedi   +3 more
doaj   +1 more source

Microstructure, texture and mechanical properties of a nickel-free high nitrogen duplex stainless steel processed through friction stir spot welding

Journal of Materials Research and Technology, 2021
A nickel-free high nitrogen duplex stainless steel holding high Mn-content was friction stir spot welded under the various rotational speeds. The microstructure/texture evolutions of the joints and the correlated mechanical properties were investigated ...
S. Yousefian, A. Zarei-Hanzaki, A. Barabi, H.R. Abedi, M. Moallemi, P. Karjalainen   +5 more
doaj   +1 more source

Unveiling the influence of dendrite characteristics on the slip/twinning activity and the strain hardening capacity of Mg-Sn-Li-Zn cast alloys

Journal of Magnesium and Alloys, 2023
This work explores the correlation between the characteristics of the cast structure (dendrite growth pattern, dendrite morphology and macro-texture) and strain hardening capacity during high temperature deformation of Mg-5Sn-0.3Li-0 and 3Zn multi ...
MS. Jalali, A. Zarei-Hanzaki, M. Mosayebi, H.R. Abedi, M. Malekan, M. Kahnooji, E. Farabi, Su-Hyeon Kim   +7 more
doaj   +1 more source

On the cyclic hardening/softening behavior of a rare earth-containing magnesium alloy during strain-controlled fatigue

Journal of Materials Research and Technology, 2022
The origin of cyclic hardening under low strain amplitude (with N = 25284 cycles to failure) followed by pseudo-plateau response under high strain amplitude (with N = 2671 cycles to failure) during fully reversal (R = −1) strain-controlled pull–push ...
A. Jeldi, A. Zarei-Hanzaki, A. Moshiri, H.R. Abedi, J.H. Cho   +4 more
doaj   +1 more source

Dynamic strain aging and twin formation during warm deformation of a novel medium-entropy lightweight steel

Journal of Materials Research and Technology, 2022
The present study deals with the extraordinary twin formation during compressive deformation of a Fe-37.55Mn-8.5Al-0.6C (wt.%) low-density steel at warm temperature regime (200–600 °C). Despite the conventional opinion regarding the restrictive effect of
Rezvan Khani, A. Zarei-Hanzaki, A. Moshiri, H.R. Abedi, Seok Su Sohn   +4 more
doaj   +1 more source

The effect of thermomechanical processing on the piezoelectric and electrical conductivity of PLA/2.5%MWCNT composite

Journal of Materials Research and Technology, 2023
The electrical properties of polymer materials, such as electrical conductivity and piezoelectricity, are significantly influenced by the ratio of amorphous to crystalline regions. Additionally, the alignment of added particles and formed crystallites is
Sahar Shahparvar, Abbas Zarei-Hanzaki, Amirhossein Farahani, Roohollah Bagherzadeh, Hamid Reza Abedi   +4 more
doaj   +1 more source

The high temperature deformation behavior of a triplex (ferrite+ austenite+ martensite) low density steel

Journal of Materials Research and Technology, 2021
The present work deals with the high temperature deformation behavior of Fe-11.15Mn-5.6Al-0.07C (wt.%) triplex ferrite-based lightweight steel in the temperature range of 800–1100 °C under the strain rate of 0.001 to 0.1s−1.
Amir-Reza Kalantari, Abbas Zarei-Hanzaki, Hamid Reza Abedi, Mohammad Sadegh Jalali, Seong-Jun Park, Jun Young Park   +5 more
doaj   +1 more source