Results 31 to 40 of about 1,206,758 (281)
Journal of Materials Research and Technology, 2021 The present work deals with revealing the fatigue and dwell-fatigue behavior and correlated damage mechanisms of Fe–Mn–Al–C lightweight steel. Surprisingly, alteration in loading mode from monotonic to cyclic induces reversible dislocation movement and ...
A. Moshiri +8 more
doaj +1 more source
On the short-time thermal phase-stability of as-cast AlCoCrFeNi2.1 eutectic high entropy alloy
Journal of Materials Research and Technology, 2022 The present work deals with the short-time thermal phase-stability of the as-cast eutectic AlCoCrFeNi2.1 high entropy alloy. Toward this end, the effect of different temperatures (800–1000 °C) and soaking times (15–60 min) on the stability of primary ...
J. Charkhchian +7 more
doaj +1 more source
A new powder encapsulation method and its implications on densification by hot isostatic pressing [PDF]
, 1993 Hot isostatic pressing is now an accepted material processing technique for the consolidation of metal powders to near-net-shape components. This thesis examines the use of coatings as in-situ envelopes to overcome the problems associated with ...
Downing, M.
core +7 more sources
Journal of Materials Research and Technology, 2022 Two lean duplex stainless steels with different manganese contents (4 and 8 wt.%) were deformed in the tensile mode in the temperature range of 25–300 °C.
Mahsa Khorrami +5 more
doaj +1 more source
Numerical Simulation of Deformation in Hot Runner Manifold
Micromachines, 2023 This study simulated the deformation of a hot runner manifold and nozzle assembly during operation, aiming to address potential leaks and premature failure. Both thermal and mechanical models were used simultaneously to accurately capture system behavior. A simplified set of boundary conditions was proposed for efficient problem-solving.
Jae Sung Jung, Sun Kyoung Kim
openaire +3 more sources
Journal of Materials Research and Technology, 2021 The present study deals with the warm temperature deformation behavior of the Ti–6Al–4V alloy throughout investigating the flow behavior and the correlated microstructure evolutions.
M. Paghandeh +6 more
doaj +1 more source
Investigation of the hot deformation of sintered titanium compacts produced from direct reduction powder [PDF]
, 2010 Includes bibliographical references (leaves 110-111).The focus of this study was the use of powder metallurgy to produce low cost titanium with comparative mechanical properties to wrought titanium.
Petersen, Shaheeda
core +1 more source
Journal of Materials Research and Technology, 2021 The strain accommodation mechanism of Ti–6Al–4V alloy with different initial microstructure; equiaxed α+β, lamellar α+β, dual phase α+ά, and fully ά martensite was studied in warm temperature deformation regime. Toward this end, a series of tensile tests
M. Paghandeh +3 more
doaj +1 more source
Learning to Predict Metal Deformations in Hot-Rolling Processes [PDF]
IEEE Robotics and Automation Letters, 2020 Accepted for publication in the IEEE Robotics & Automation Letters (2020)
R. Omar Chavez-Garcia +6 more
openaire +3 more sources
Y Addition Effects on Hot Deformation Behavior of Cu-Zr Alloys with High Zr Content [PDF]
Archives of Metallurgy and Materials, 2018 Isothermal hot compression experiments were carried out using the Gleeble-1500D thermal mechanical simulator. The flow stress of the Cu-1%Zr and Cu-1%Zr-0.15%Y alloys was studied at hot deformation temperature of 550°C, 650°C, 750°C, 850°C, 900°C and the
K. Tian +5 more
doaj +1 more source