Results 51 to 60 of about 226,190 (309)
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
The structural and diagenetic evolution of injected sandstones: examples from the Kimmeridgian of NE Scotland [PDF]
, 2003 : Injected sandstones occurring in the Kimmeridgian of NE Scotland along the bounding Great Glen and Helmsdale faults formed when basinal fluids moved upward along the fault zones, fluidizing Oxfordian sands encountered at shallow depth and injecting ...
Duranti, D. +4 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Journal of Materials Research and TechnologyTwo α′-containing microstructures, a fully martensitic (α′) structure and a dual-phase α+α′ structure (≈45–50 % α′), were generated in Ti–6Al–4V by solution-treatment above and below the β-transus, followed by water quenching.
H.R. Abedi +3 more
doaj +1 more source
Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres
Advanced Engineering Materials, EarlyView.This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann +3 more
wiley +1 more source
Orbital and spin relaxation in single and coupled quantum dots [PDF]
, 2006 Phonon-induced orbital and spin relaxation rates of single electron states in lateral single and double quantum dots are obtained numerically for realistic materials parameters.
A. M. Alcalde +5 more
core +3 more sources
Hot Deformation Behavior of Haynes 25 by the Hot Tensile Test [PDF]
Journal of Advanced Materials In Engineering, 2019 In the present work, hot tensile behavior of Haynes 25 Co-base alloy was investigated in the temperature range of 950-1200 ˚C and 0.1 s-1. Thermodynamic calculations showed that M23C6 and M6C carbides were stable below 1000 ˚C and above 1050 ˚C, respectively. Stress-strain curves also indicated an unusual trend of strain fracture.
M. Samii Zafarghandi, S. M. Abbasi
openaire +2 more sources
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
The hot deformation behaviors and constitutive modeling of Hastelloy C276
Materials Research Express, 2023 Hastelloy C276 is widely used in the new generation of nuclear power plants, and hot deformation is the optimum way to form the C276 part. In this investigation, the hot deformation and constitutive modeling of Hastelloy C276 alloy are researched, and ...
Jia-Fu Wu +3 more
doaj +1 more source