Results 101 to 110 of about 264,889 (342)

Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)

Advanced Engineering Materials, EarlyView.
Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho, M. Naeem, T. H. C. Costa, M. S. Libório, J. C. A. Queiroz, C. B. B. Luna, R. R. M. Sousa, P. S. Vieira, E. M. Araújo   +8 more
wiley   +1 more source

Hot deformation behavior of Hastelly C276 superalloy

Transactions of Nonferrous Metals Society of China, 2012
Hot tensile behavior of C276 superalloy was studied in the deformation temperature range of 650-750 degrees C with the strain rate range of 0.35-35 mm/s. The results show that deformation temperature and strain rate both have significant influence on the flow stress.
Yan-ling LU, Jin-xi LIU, Xiao-ke LI, Jian-ping LIANG, Zhi-jun LI, Guan-yuan WU, Xing-tai ZHOU   +6 more
openaire   +1 more source

Effects of Mn addition and related Mn-containing dispersoids on the hot deformation behavior of 6082 aluminum alloys

Materials Science & Engineering: A, 2019
The hot deformation behaviors of 6082 aluminum alloys containing different Mn contents (0.05–1.0 wt%) were systematically investigated by uniaxial compression tests in a temperature range of 400–550 °C and strain rate range of 0.001–1 s-1.
Xiaoming Qian, N. Parson, X.-Grant Chen
semanticscholar   +1 more source

Austenite grain growth and hot deformation behavior in a medium carbon low alloy steel

, 2020
To examine the austenite grain growth behavior and kinetics under isothermal austenitization process in a low alloy medium carbon forged steel, heat treatments at different temperatures (1150, 1175, 1200, and 1260 °C) and times (5, 15, and 25 min) were ...
A. Chamanfar, S. Chentouf, M. Jahazi, L. Lapierre-Boire   +3 more
semanticscholar   +1 more source

Encyclopedia of 2D β′‐In2Se3 Growth Using Chemical Vapor Deposition: The Effects of Synthesis Parameters Onto Material Quality

Advanced Engineering Materials, EarlyView.
A distinct semi‐confined inner‐tube chemical vapor deposition geometry enables reproducible, large‐area growth of phase‐pure 2D β′‐In2Se3 from InI + Se precursors. Engineering local vapor transport and optimizing precursor delivery and temperature–time conditions yield uniform continuous films.
Dasun P. W. Guruge, P. Sanju S. Panawala, Joseph F. S. Fernando, Zhenhuan Chen, Chao Zhang, Dong‐Chen Qi, Liangzhi Kou, Konstantin L. Firestein, Dmitri V. Golberg   +8 more
wiley   +1 more source

Study on the behavior of small droplet impinging onto a hot surface

, 2011
This paper was presented at the 3rd Micro and Nano Flows Conference (MNF2011), which was held at the Makedonia Palace Hotel, Thessaloniki in Greece.
Tagashira, K, Kohno, M, Takata, Y, Fukuda, S, Ishihara, N, Hidaka, S, Arita, M, 3rd Micro and Nano Flows Conference (MNF2011)   +7 more
core  

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Regulation of high-temperature microstructure evolution and recrystallization by pre-strain accumulation in Al–Zn–Mg–Cu alloys

Journal of Materials Research and Technology
This study systematically investigates the hot deformation behavior of Al–Zn–Mg–Cu alloy through pre-deformation compression tests at different temperatures (room temperature, RT, and cryogenic temperature, CT) with varying pre-strain levels, combined ...
Dejin Wei, Guoqun Zhao, Luyi Han, Kunpeng Deng   +3 more
doaj   +1 more source

Microstructural evolution of AISI304 stainless steel in the Steckel Mill rolling process

, 2004
Includes bibliographical references (leaves [105]-110).The microstructural evolution of AISI304 stainless steel in the Steckel mill rolling process is investigated.
Parker, Sa-aadat
core  

Hot deformation behavior of spray formed FGH4095

Acta Physica Sinica, 2012
For the numerical simulation of hot working process of spray-formed FGH4095, the high temperature deformation behavior of spray-formed FGH4095 is studied at different deformation temperatures (1010-1140 ℃) and different strain rates (0.001-10.0 s-1) using Gleeble 3800 thermal simulator. The constitutive equation is established with the sinh model.
null Zhang Yu, null Ge Chang-Chun, null Guo Biao, null Shen Wei-Ping   +3 more
openaire   +1 more source