Results 31 to 40 of about 23,122 (306)
Results in Physics, 2019 Magnesium matrix composites reinforced with short carbon fiber (SCF) (SCF/AZ31B composites) were fabricated by multi-times hot-extrusion with mass fraction of 3%. The effect of extrusion times and addition of SCFs on microstructure, mechanical properties
Zhao Yang +4 more
doaj +1 more source
Structural characterization of aluminium alloy 7075–graphite composites fabricated by mechanical alloying and hot extrusion [PDF]
, 2014 The modification on the microstructure and mechanical response of some Al7075–graphite composites fabricated by mechanical alloying and hot extrusion were studied as a direct function of milling time (0–10 h) and graphite concentration (0–1.5 wt.%).
IVANOVICH ESTRADA GUEL +1 more
core +1 more source
Predicting Residence Time and Melt Temperature in Pharmaceutical Hot Melt Extrusion
Pharmaceutics, 2023 Hot-melt extrusion is increasingly applied in the pharmaceutical area as a continuous processing technology, used to design custom products by co-processing drugs together with functional excipients.
Judith Winck +2 more
doaj +1 more source
Recent development, challenges, and prospects of extrusion technology
Future Foods, 2021 There is a significant advancement in the modification of extruders for the commercial application in food processing sector, especially during the last three decades.
Krishna Prabha +6 more
doaj +1 more source
Influence of degassing on hot-melt extrusion process [PDF]
European Journal of Pharmaceutical Sciences, 2015 The present study aimed to evaluate the effect of degassing on an extrusion process, with respect to extrudate quality and drug release properties. Processed formulations were extruded with and without a degassing vent port at various locations along the barrel. All the experiments were performed under constant processing temperature, feeding rate, and
Saad M, Alshahrani +5 more
openaire +2 more sources
Investigation of Hot-extrusion Effect on Microhardness, Microstructure and Corrosion Behavior of Magnesium-based Bio-composites [PDF]
Journal of Stress Analysis, 2019 Magnesium alloys are a unique choicefor orthopedic implants due to their biocompatibility and biodegradability properties. In this article, the impact of hot-extrusion process is investigated on microhardness, microstructure, and corrosion behavior of ...
E. Ghazizadeh +2 more
doaj +1 more source
Solid state recycling of used aluminum alloy beverage cans by thermomechanical consolidation
Heat Treatment and Surface Engineering, 2022 Solid-state recycling of used aluminum alloy beverage cans was accomplished by thermomechanical consolidation of the sheet fragments produced by shredding the cans.
Ziyi Wang +7 more
doaj +1 more source
, 2013 This paper describes a detailed study of tube extrusion by simulation using finite element method (FEM). The finite element model used one-sixth of symmetry. The extrusion load, emperature evolution and metal flow were predicted.
Sheppard, Terry, Velay, Xavier, Niu, L.
core +1 more source
MICROSTRUCTURE AND THERMAL STABILITY OF Al-Fe-X ALLOYS
Acta Metallurgica Slovaca, 2018 In this work, Al-11Fe, Al-7Fe-4Ni and Al-7Fe-4Cr (in wt. %) alloys were prepared by combination of casting and hot extrusion. Microstructures of as-cast alloys were composed of aluminium matrix with large and coarse intermetallics such as Al13Fe4 ...
Andrea Školáková +5 more
doaj +1 more source
Journal of Materials Research and Technology, 2022 The MgZn1.2Zr0.35 (wt%) alloys for orthopedic applications enhanced by small amount addition of zirconium and subsequent hot extrusion working based on cast MgZn1.2 system were successfully fabricated.
Jun Fan +8 more
doaj +1 more source