Results 1 to 10 of about 1,171,203 (263)
Effects of Zn content on Hot Tearing Susceptibility of Mg–7Gd–5Y–0.5Zr Alloy [PDF]
Metals, 2020 Mg−7Gd−5Y−0.5Zr alloy has excellent mechanical properties but poor hot tearing resistance. The latter makes it difficult to cast billets, which limits the size of subsequently processed parts.
Ziqi Wei +6 more
doaj +5 more sources
Hot tearing susceptibility of MgZn4.5YxZr0.5 alloys and mechanism [PDF]
China Foundry, 2016 The hot tearing susceptibility of MgZn4.5YxZr0.5 (x = 0.5, 1, 2, 4, 6) alloys was evaluated using Clyne−Davies’ theoretical model and a constrained rod casting (CRC) apparatus equipped with a load cell and data acquisition system.
Yu Feng, Ping-li Mao, Zheng Liu
doaj +4 more sources
Journal of Magnesium and Alloys, 2018 Based on the hot tearing index |∆T/∆(fs)0.5| recently proposed by Kou and the thermodynamic calculations of Pandat software, Al, Cu, and Mn elements were picked up and their influence on hot tearing susceptibility of Mg–xZn (x = 6, 8, 10, wt%) alloys was
Zhenzhen Yang +6 more
doaj +4 more sources
A review on hot tearing of magnesium alloys [PDF]
Journal of Magnesium and Alloys, 2016 Hot tearing is often a major casting defect in magnesium alloys and has a significant impact on the quality of their casting products. Hot tearing of magnesium alloys is a complex solidification phenomenon which is still not fully understood, it is of ...
Jiangfeng Song +5 more
doaj +4 more sources
Hot Tearing, Parameters, and Mould Types for Observation – Review [PDF]
Archives of Foundry Engineering, 2022 Hot tearing is a casting defect responsible for external and internal cracks on casting products. This irregular undesired formation is often observed during solidification and freezing.
Akhyar
doaj +3 more sources
Effect of Strontium Inoculation on Hot Tearing in Aluminium Alloys [PDF]
Archives of Metallurgy and Materials, 2018 Main aim of submitted work is evaluation and experimental verification of inoculation effect on Al alloys hot-tear sensitivity. Submitted work consists of two parts.
D. Bolibruchová +3 more
doaj +3 more sources
Metals, 2023 Aluminum alloys 5083, 6061, and 7075 are prone to hot tearing under direct-chill casting conditions; the defects that form during solidification of those alloys are highly sensitive to variation in the alloying elements, with these elements commonly ...
Kai-Yu Liang +6 more
doaj +2 more sources
Materials & DesignThe Al-Zn-Mg-Cu alloy is widely used in automotive lightweighting and other applications due to its excellent mechanical properties. However, when this alloy is cast using metal molds, it exhibits high hot tearing susceptibility (HTS), increasing the ...
Pengfei Li +5 more
doaj +3 more sources
Hot tearing behavior of NZ30K Mg alloy under progressive solidification [PDF]
China Foundry, 2021 Progressive solidification is usually considered an effective strategy to reduce the hot tearing susceptibility of a cast component. In this study, special constrained plate castings with progressive changes in cross-section were designed, which enabled ...
Ke Wang, Peng-huai Fu, Li-ming Peng
doaj +1 more source
Influence of a low-frequency alternating magnetic field on hot tearing susceptibility of EV31 magnesium alloy [PDF]
China Foundry, 2021 The effect of a low-frequency alternating magnetic field (AMF, 0 A 0 Hz, 5 A 10 Hz, 10 A 10 Hz, 15 A 10 Hz) on the hot tearing susceptibility (HTS) of a magnesium alloy (EV31) was systematically studied using a combination of experiment and numerical ...
Xin Su, Zhi-jun Feng, Jing-fu Huang
doaj +1 more source