Results 21 to 30 of about 14,276 (253)
Hot-thermistor spirometry for the artificial ventilation of infants [PDF]
, 1982 Bibliography: leaves 230-245.This thesis describes equipment and techniques which were developed for use in monitoring mechanical aspects of artificial ventilation and optimising ventilation procedures.
Hughes, Timothy John
core
Advanced Engineering Materials, EarlyView.Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati +11 more
wiley +1 more source
Multilayer Self‐Limiting Electrospray Deposition via Stepped Voltage Bias
Advanced Engineering Materials, EarlyView.Self‐limiting electrospray deposition (SLED) uses a high voltage to generate and deposit a charged payload on a target surface. The coating retains its charge, repelling newly arriving material. SLED thickness can be decreased by applying a secondary bias to the target.
Madhuri Deb +3 more
wiley +1 more source
Narrow gap laser welding by multilayer hot wire addition [PDF]
, 2016 Welding of thick section butt joints experiences limitations for different techniques. One option is to fill a narrow gap layer by layer with laser melted wire, a laser metal deposition technique where the complexity of a keyhole is avoided.
Bang, Han-Sur, +11 more
core +1 more source
Counterion Dependent Side‐Chain Relaxation Stiffens a Chemically Doped Thienothiophene Copolymer
Advanced Functional Materials, EarlyView.Oxidation of a thienothiophene copolymer, p(g3TT‐T2), via different doping strategies and dopant molecules resulted in materials with similar oxidation levels and a high electrical conductivity of ≈100 S cm−1. However, mechanical properties varied significantly, with sub‐glass transition temperatures and elastic moduli spanning from –44°C to –3°C and ...
Mariavittoria Craighero +12 more
wiley +1 more source
A technique for the dynamic calibration of hot wire anemometers [PDF]
, 1966 Technique for dynamic calibration of hot wire ...
Potter, R. C.
core +1 more source
Research and development of a laser hot wire deposition process [PDF]
, 2021 “Laser hot wire directed energy deposition (DED) is an increasingly popular method for improving deposition rates and overall reduction of build times in DED processing.
Croft, Christopher
core +1 more source
Advanced Functional Materials, EarlyView.ABSTRACT Electronic waste has emerged as a major environmental challenge, driven by the massive consumption and a limited lifetime of modern electronic devices, stimulating the development of sustainable electronics. Here, an all‐biomaterial gelatin‐choline‐citric acid ([Ch][CA]) ionogel is developed as an active binder to realize self‐sintered ...
Lin Guo +10 more
wiley +1 more source
A study of the turbulent wake of an airfoil in an air stream with a 90° curvature using hot-wire anemometry and large eddy simulation [PDF]
, 2008 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.The broad aim of the work presented in this thesis is to investigate the wake of an airfoil under the combined effects of streamwise curvature and pressure ...
Farsimadan, Ehsaan
core
Advanced Functional Materials, EarlyView.Here, we provide the reader with the current state of the art in the fabrication of high‐T2‐coherence diamond, optimized through the use of double electron–electron resonance (DEER) spectroscopy. We reveal the main as well as yet unidentified spin defects, the reduction of which is essential for reducing the spin bath and fabricating materials for ...
Olga Rubinas +6 more
wiley +1 more source