Results 51 to 60 of about 2,129 (183)

Flow stress behavior, constitutive modeling, processing map and microstructure evolution in hot deformation of Fe-7.1Al-0.7Mn-0.4C-0.3Nb alloy

Journal of Materials Research and Technology
The automotive industry has experienced rapid growth, with lightweight materials becoming a significant research focus. Among these materials, low-density Fe–Mn–Al–C alloys show promise for this kind of application.
Mônica Aline Magalhães Gurgel, Duílio Norberto Ferronatto Leite, Luciano Pessanha Moreira, Andersan dos Santos Paula, Eustáquio de Souza Baêta Júnior, Rodolfo da Silva Teixeira, Luiz Paulo Brandao   +6 more
doaj   +1 more source

Digital Pathology in Hematopathology: From Vision to Deployment

International Journal of Laboratory Hematology, Volume 48, Issue 3, Page 531-540, June 2026.
ABSTRACT Digital pathology (DP) has evolved alongside other technical advances, transforming our daily lives and diagnostic medicine. It is likely that, as in other areas of life, science, and medicine, the overall level of digitization will continue to rise, along with an increasing number of groups implementing DP.
Ryan C. Shean, Anton V. Rets
wiley   +1 more source

Revealing the dynamic recrystallization and deformation instability of TiC reinforced AZ61 composites with uniform structure and bimodal grain structure

Journal of Magnesium and Alloys
Although microstructural configuration significantly enhances composites' comprehensive mechanical properties, its influence on hot deformation remains unclear.
Lingling Fan, Ying Zeng, Lingbao Ren, Yanyan huang, Kunyang Fan, Zhenyu Zhu, Ran Ni, Gaofeng Quan, Wei Feng, Hajo Dieringa   +9 more
doaj   +1 more source

High Temperature Strength and Hot Working Technology for As-Cast Mg–1Zn–1Ca (ZX11) Alloy

Metals, 2017
Cast Mg–1Zn–1Ca alloy (ZX11) has been tested to evaluate its compressive strength between 25 °C and 250 °C, and workability in the range of 260–500 °C. The ultimate compressive strength of this alloy is about 30% higher than that of creep-resistant alloy
Kamineni Pitcheswara Rao, Kalidass Suresh, Yellapregada Venkata Rama Krishna Prasad, Chalasani Dharmendra, Norbert Hort, Hajo Dieringa   +5 more
doaj   +1 more source

Data‐Driven Discovery of Quaternary Ammonium Interlayers for Efficient and Thermally Stable Perovskite Solar Cells

Advanced Materials, Volume 38, Issue 28, 18 May 2026.
An active learning framework, grounded in independently generated in‐house experimental data, enables reliable discovery of high‐performance interfacial materials for perovskite solar cells. Iterative model refinement autonomously converges toward structurally robust quaternary ammonium architectures, establishing a new design principle for interfacial
Jongbeom Kim, Yang Jeong Park, Chaehoon Jeon, Nahye Shin, Jaewang Park, Seungun Lee, Jino Im, Sungroh Yoon, Sang Il Seok   +8 more
wiley   +1 more source

Optimization of Thermo-Mechanical Processing for Forging of Newly Developed Creep-Resistant Magnesium Alloy ABaX633

Metals, 2017
The compressive strength and creep resistance of cast Mg-6Al-3Ba-3Ca (ABaX633) alloy has been measured in the temperature range of 25 to 250 °C, and compared with that of its predecessor ABaX422.
Kamineni Pitcheswara Rao, Chalasani Dharmendra, Yellapregada Venkata Rama Krishna Prasad, Norbert Hort, Hajo Dieringa   +4 more
doaj   +1 more source

A Review of the Unintended Consequences of Biochar in Various Applications

Advanced Energy and Sustainability Research, Volume 7, Issue 5, May 2026.
Biochar is widely promoted as a sustainable material for applications ranging from soil amendment to energy storage and construction materials. This review critically examines the often‐overlooked and unintended consequences of biochar, including variability in properties, safety risks, and performance limitations.
Singaravelu Vivekanandhan, Elif Kaynak, Dong Wang, Vigneshwaran Shanmugam, Aurelio Bifulco, Julio Diarte Almada, Imelda Saran Piri, Zhengyang Wang, Lokesh P. Padhye, Nam Kyeun Kim, Michael Försth, Jaime Gonzalez‐Libreros, Igor Wachter, Sabrina Karim, Oisik Das   +14 more
wiley   +1 more source

Constitutive Modelling and Hot Workability Analysis by Microstructure Examination of GH4169 Alloy

Crystals, 2018
The relationships between hot deformation parameters and flow behaviour have attracted many researchers’ attention for the past few decades, whilst precise constitutive modelling of GH4169 remained a problem, which seriously affected the process ...
Rongchuang Chen, Zhizhen Zheng, Jianjun Li, Fei Feng   +3 more
doaj   +1 more source

Revealing the Influence of SiC Particle Size on the Hot Workability of SiCp/6013 Aluminum Matrix Composites. [PDF]

Materials (Basel), 2023
Chen S, Wu C, Bo G, Liu H, Tang J, Fu D, Teng J, Jiang F.   +7 more
europepmc   +1 more source

Hot Workability of the Multi-Size SiC Particle-Reinforced 6013 Aluminum Matrix Composites. [PDF]

Materials (Basel), 2023
Wu C, Chen S, Tang J, Fu D, Teng J, Jiang F.   +5 more
europepmc   +1 more source