Results 151 to 160 of about 5,682 (202)
Some of the next articles are maybe not open access.
Tensile Testing of HVOF-Sprayed Coatings
International Thermal Spray Conference, 1999Abstract In this paper, the Young's modulus, Poisson's ratio, and ultimate tensile strength of HVOF-sprayed NiCr (80/20) coating are evaluated by a uniaxial tensile test parallel to the coating plane. The effect of stand off distance is also considered.
Varis, Tommi +3 more
openaire +4 more sources
Designs and Preparation of Advanced HVOF-PVD Duplex Coating by Combination of HVOF and Arc Ion Plating [PDF]
Abstract Advanced HVOF-PVD duplex coatings were produced on the medium carbon steel by combinations of High Velocity Oxygen-Fuel (HVOF) and arc ion plating. The microstructures and mechanical properties were investigated by means of X-ray diffraction (XRD), scanning electron microscopy (SEM) in association with mechanical property measurement.
Xianna Meng, Wanglin Chen
exaly +2 more sources
Effect of Different HVOF Coatings on the Tribological Behavior of PVD/HVOF Duplex Coatings
Tribology InternationalLei Shao, Wensheng Li, Canming Wang
exaly +2 more sources
International Thermal Spray Conference, 2004
Abstract A secondary acetylene after burner attached with an HVOF gun has been developed to produce high quality coatings required of ceramics. The secondary burner adds heat energy, enough to make deposition, to fine ceramic particles heated and accelerated by an HVOF gun.
T. Morishita, S. Osawa, T. Itsukaichi
openaire +1 more source
Abstract A secondary acetylene after burner attached with an HVOF gun has been developed to produce high quality coatings required of ceramics. The secondary burner adds heat energy, enough to make deposition, to fine ceramic particles heated and accelerated by an HVOF gun.
T. Morishita, S. Osawa, T. Itsukaichi
openaire +1 more source
Nanoreinforced HVOF-Sprayed Ceramic Coatings
International Thermal Spray Conference, 2005Abstract HVOF thermal spraying has been developed to deposit dense Al2O3-coatings with improved protective properties for various applications. Nanocrystalline coatings have been found to offer better thermal shock resistance, lower thermal conductivity and better wear resistance than their conventional counterparts.
Turunen, Erja +5 more
openaire +3 more sources
Mechanical Properties of Nanocrystalline HVOF Coatings
Materials Science Forum, 2006Thermal spraying (TS) is increasingly used to deposit thick wear resistant coatings on machine and equipment parts. Therefore, it is of uttermost importance to know their mechanical properties in order to tailor and optimize the coatings for various applications.
Hannula, Simo-Pekka +3 more
openaire +3 more sources
Standard HVOF Process Compared to the HVOF Process for Internal Coating with Fine Powders
International Thermal Spray Conference, 2008Abstract The main argument against the use of the internal HVOF process is the high thermal stress to which the substrates are subjected during the coating process. Traditional HVOF guns operate with a flame-stream energy level of 100–200 kW. Rendering HVOF technology usable for the application of internal coatings requires the reduction
G. Matthaeus +5 more
openaire +1 more source
HVOF Coating and Characterization
2014HVOF Coating is one of the thermal barrier coatings to protect surfaces from high temperature, corrosion, and erosion environments. Coating characteristics including thickness, metallurgy, elemental composition, and morphology play an important role in practical applications.
Bekir Sami Yilbas +2 more
openaire +1 more source
Optimized HVOF Titania Coatings
Journal of Thermal Spray Technology, 2003A series of spray parameters was tested for a titania (TiO2) feedstock, and the in-flight particle temperature was measured for each setting combination. The parameter set that resulted in the highest particle temperature was selected for producing coatings for further study and analysis.
R. S. Lima, B. R. Marple
openaire +1 more source
Cavitation Erosion of HVOF Coatings
International Thermal Spray Conference, 1996Abstract The proposed paper reports a series of experiments to investigate the cavitation erosion mechanism of HVOF coatings. Vibratory cavitation erosion tests according to ASTM G 32 have been carried out with several HVOF coatings including cermets, oxides and metallic alloys.
R. Schwetzke, H. Kreye
openaire +1 more source

