Results 41 to 50 of about 5,682 (202)

Performance Analysis of Abradable Coating Systems for Aircraft Gas Turbines

open access: yesAdvanced Engineering Materials, Volume 28, Issue 15, 5 August 2026.
Three CoNiCrAlY/YSZ/MgAl2O4 abradable liner configurations on a nickel‐superalloy are evaluated by thermal‐gradient cycling and incursion tests. Laser ablation of the bondcoat and/or Y2O3‐stabilized ZrO2 (YSZ) intermediate layer increases mechanical interlocking and bonding for thick topcoats.
Hanna Heyl   +4 more
wiley   +1 more source

Environmental Barrier Coatings Deposited by Suspension Plasma Spraying

open access: yesJournal of the American Ceramic Society, Volume 109, Issue 7, July 2026.
By taking advantages of high deposition temperature, fully crystalline, crack‐free Yb2Si2O7 EBCs were successfully obtained by suspension plasma spray. However, high amount of Yb2SiO5 phase was found in the as‐sprayed coatings. The formation mechanism of the high amount of Yb2SiO5 phase might be attributed to the high surface ration of the particle for
Dapeng Zhou   +4 more
wiley   +1 more source

Dynamic Testing of Cold Gas Sprayed Bipolar Plates–Porous Transport Layer Coating System in Proton Exchange Membrane Water Electrolysis

open access: yesAdvanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.
Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin   +5 more
wiley   +1 more source

Microstructure and properties of APS/HVOF thermal sprayed WC-based cermet coatings

open access: yes工程科学与技术, 2017
:Due to high hardness, great wear resistance and good corrosion resistance, WC-based coatings are widely used in industry to increase the wear resistance and corrosion resistance of components.
lishenhou   +4 more
doaj  

Characterization of Macro/Microstructure and Corrosion Resistance of Austenitic Gas Tungsten Arc Welding Cladding

open access: yesAdvanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.
Cladding is a proven method that boosts the surface qualities of mechanical parts by applying a layer of more durable material over a base substrate. This work responds to the needs of offshore and pressure vessels sectors by focusing on cladding a super austenitic steel onto low‐carbon steel through gas tungsten arc welding.
E. J. da Cruz Junior   +6 more
wiley   +1 more source

STUDY OF STRUCTURAL-PHASE CHARACTERISTICS OF ZrCN COATINGS UNDER THE INFLUENCE OF HVOF PROCESS PARAMETERS

open access: yesШәкәрім университетінің хабаршысы: Техника ғылымдар
This study investigates the effect of oxygen pressure during high-velocity oxy-fuel (HVOF) spraying on the formation and structural-phase characteristics of ZrCN coatings deposited on 65G steel. The coatings were produced using the Termika-3 system under
Sh. R. Kurbanbekov   +3 more
doaj   +1 more source

Advanced Functional Materials for Marine Energy Utilization

open access: yesInterdisciplinary Materials, Volume 5, Issue 3, Page 317-356, May 2026.
Marine renewable energy is an important future clean energy supply. We construct and sort out the material system for marine energy capture and conversion, transmission, storage, and utilization for the first time. ABSTRACT Several features of marine energy, including large reserves, sustainable utilization, environmental friendliness, make it a ...
Qiang Yu   +7 more
wiley   +1 more source

Identifying the optimal HVOF spray parameters to attain minimum porosity and maximum hardness in iron based amorphous metallic coatings

open access: yesDefence Technology, 2017
Flow based Erosion – corrosion problems are very common in fluid handling equipments such as propellers, impellers, pumps in warships, submarine. Though there are many coating materials available to combat erosion–corrosion damage in the above components,
S. Vignesh   +3 more
doaj   +1 more source

Corrosion and wear protection of AISI 4140 carbon steel using a laser-modified high-velocity oxygen fuel thermal sprayed coatings

open access: yesJournal of Electrochemical Science and Engineering, 2022
Inconel and micro and nano WC-12Co powders were deposited on AISI 4140 carbon steel by high-velocity oxy fuel (HVOF) coating and followed by laser surface modification. Laser power and scan speed were varied at different levels.
Shanmugasundaram Sivarajan   +4 more
doaj   +1 more source

Numerical Prediction of Deformation‐Induced Martensitic Transformation in Cold‐Sprayed Austenitic Stainless Steel

open access: yessteel research international, Volume 97, Issue 4, Page 2241-2249, April 2026.
Cold spray deposition of stainless steel (grade: SS304) is evaluated for marine applications, with emphasis on martensitic transformation during impact. Analytical modeling, simulations, and experiments reveal that helium‐assisted spraying of fine powders promotes cooling below the martensitic start temperature, enabling up to ≈40% austenite to ...
Cal Vin Wong   +4 more
wiley   +1 more source

Home - About - Disclaimer - Privacy