Results 61 to 70 of about 66,002 (291)

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Adaptive impact resistance support method for advanced hydraulic supports in mines based on digital twins and deep reinforcement learning

Gong-kuang zidonghua
Due to the disturbance of geological disasters such as deep mining and rock burst, there are problems such as poor self perception capability, weak intelligent anti impact adaptive capability, and lack of decision-making and control capability in the ...
ZHANG Fan, SHAO Guangyao, LI Yuhan, LI Yuxue   +3 more
doaj   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Mining technology and support optimization design of super high fully mechanized caving and small mining ratio in hard and extra thick coal seam

Meikuang Anquan, 2021
In order to realize the safety, high efficiency and high recovery rate mining of 9-13 m thickness hard coal seam in Jinjitan Coal Mine, the top coal recovery rate and coal wall stability of different cutting heights are analyzed by theoretical analysis ...
MENG Xiangjun, ZHANG Jinhu, LI Mingzhong, YUE Ning, XU Yongxiang, TONG Peng, CAI Fenghua   +6 more
doaj   +1 more source

Research on evaluation model of comprehensive condition for mine-used hydraulic support

Gong-kuang zidonghua, 2019
In view of problem that existing hydraulic support monitoring system had not realized comprehensive monitoring and evaluation of conditions of hydraulic support, evaluation model of comprehensive condition for hydraulic support was established.Through ...
HOU Gang
doaj   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Multimodal Soft Surgical Robots Enabled by Eco‐Degradable, Sterilizable Polymers and Transient Electronics

Advanced Functional Materials, EarlyView.
A compostable PGS soft surgical robot with interchangeable modules integrates transient Mo tactile and Si thermal sensors for dual feedback. The device preserves its function after clinical‐grade sterilization, demonstrates stable actuation and cardiac tissue grasping with real‐time in vivo pulsatile monitoring, and biodegrades post‐use with soil‐safe, 
Minseong Chae, Kyung‐Sub Kim, Gyeong‐Seok Hwang, Jun‐Seok Shim, Sung‐Woo Kim, Yong‐Wu Kim, Jieun Han, Jae‐Young Bae, Jae‐Hwan Lee, Minjung Chae, Jooik Jeon, Joo‐Hyeon Park, You‐Jung Park, Ju‐Yong Lee, Sung‐Geun Choi, Min‐Ha Oh, Yong‐Joong Shin, Young‐In Ryu, Ji‐Woo Gu, Seong‐Yu Choi, Jeong‐Yun Sun, Jung Keun Hyun, Myoung‐Ryul Ok, Sang Yup Kim, Edyta Wyszkowska, Ju‐Young Kim, Kang‐Sik Lee, Seung‐Kyun Kang   +27 more
wiley   +1 more source

Transfer Printing and Reconfiguration of Soft Electronics Using Digital Microfluidics and Laser Machining

Advanced Functional Materials, EarlyView.
This paper presents a digital microfluidics‐based technique for transferring and reconfiguring soft nanomembranes. Laser‐machined nanothin membranes are picked up, transported, and aligned via tailored surface tension and the actuation of water droplets, enabling the development of flexible electronics, the integration of functional materials on 3D ...
Quang Anh Nguyen, Chi Cong Nguyen, Tran Bach Dang, Phuoc Thien Phan, Jordan Thorpe, Michael Listyawan, Nhat Minh Doan, Sinuo Zhao, Hongru Chen, Trung Thien Hoang, Mingsheng Xu, Jisheng Han, Thanh Nho Do, Adam Hill, Timothée Mouterde, Hoang‐Phuong Phan   +15 more
wiley   +1 more source

Expert system prototype for hydraulic system design focusing on concurent engineering aspects / [PDF]

, 1998
Tese (Doutorado)- Universidade Federal de Santa Catarina, Centro ...
Silva, Jonny Carlos da
core  

3D Printing Innovations in Polymeric Porous and Patterned Architecture

Advanced Functional Materials, EarlyView.
Polymeric foams occupy a unique structural space between dense solids and open networks, where engineered void fraction governs mechanical compliance, thermal resistance, and mass transport. Additive manufacturing now enables precise spatial control over cellular architecture, unlocking designer foam structures across applications spanning crash ...
Dhanush Patil, Sri Vaishnavi Thummalapalli, Clarissa Westover, Arunachalam Ramanathan, M. Taylor Sobzcak, Roumika Patil, Qixuan Xiang, Tiantian Li, Sui Yang, Timothy E. Long, Hongyue Sun, Xianqiao Wang, Yang Liu, Kenan Song   +13 more
wiley   +1 more source