Results 41 to 50 of about 172 (153)

摆线齿准双曲面齿轮模拟加工系统的界面设计及相关检验

Jixie chuandong, 2013
The interface design principle and constitution of simulation machining system of epicycloidal hypoid gears is briefly introduced.The interface content of simulation machining system of epicycloidal hypoid gear is described in detail,including interface ...
李权才, 王星星, 付丽, 乔雪涛
doaj  

Influence of Shaft Offset, Rotational Speed, Spiral Angle and Torque on Efficiency and Power Losses in Automotive Hypoid Gear Train using Simulation Tool

International Journal of Automotive Science and Technology
The complex geometry with sliding contact surfaces of hypoid gear pair with differential unit in automotive vehicles results in increased frictional losses and reduced mechanical efficiency.
Dr. Shıvakumar Nagareddy, Ravi Subramanyam, Vijay Govindarasu   +2 more
doaj   +1 more source

基于时钟细分法的弧齿锥齿轮传动误差测量研究

Jixie chuandong, 2012
To improve the meshing quality and the performance of the driving mechanism in spiral bevel and hypoid gears,an approach of a fixed frequency clock signal to subdivide the pulse of angular displacement sensor was proposed,and the transmission error（T.E.）
徐爱军, 邓效忠, 徐恺, 李聚波, 张静   +4 more
doaj  

基于现代分析技术对准双曲面齿轮进行加载接触分析

Jixie chuandong, 2012
Based on the theory of HFT（hypoid gear formate tilt） for Manufacturing hypoid gears,according to the feature of formate for gears and Generate for pinions,coordinate systems are built for generating pair of gears,then the equations of tooth,coign and ...
蒋闯, 邓效忠, 张华
doaj  

The mathematical model of non-circular crossed-axis gear

Advances in Mechanical Engineering, 2023
Non-circular crossed gear can be regarded as the general form of the single stage gear, which can be converted into hypoid gearing, non-circular bevel gearing, non-circular external gearing, and non-circular internal gearing with specific parameters ...
Can Yang, Junwei Wang, Zhigang Fang, Fangyan Zheng   +3 more
doaj   +1 more source

An Indirect Evaluation method for Running Stability of Hypoid Gears

Jixie chuandong, 1999
This paper resents an indirect method to evaluate running stability of hypoid gears, in which the sign of vibration of driven shaft bearing housing in the rolling checker is detected as a measure value of running stability of meshing gears.
黄昌华, 王季军, 王人成, 廖绍华, 李润方   +4 more
doaj  

遗传算法在高齿准双曲面齿轮设计中的应用

Jixie chuandong, 2005
Based on Genetic algorithm, the optimization of high tooth hypoid gear is developed, which could enlarge the tooth height without undercut and ensure thickness of tooth top.
王军, 汤黎明, 曹雪梅, 邓效忠
doaj  

研齿对准双曲面齿轮副动态性能的影响

Jixie chuandong, 2007
Mechanism of the lapping influence on the dynamic behavior of hypoid gears is analyzed. Based on the lapping practice, the driving vibration and noise of gears before lapping and after under various rotational speeds and loads have been tested and ...
魏冰阳, 谢建军
doaj  

Accurate Tooth Lead Crowning without Twist in Cylindrical Helical Gear Grinding

Advances in Mechanical Engineering, 2014
Form grinding is a popular finishing process in manufacturing cylindrical gears with tooth flank modification. The tooth flanks are usually twisted when a lead crowning is performed only through additional radial motion during double flank grinding.
Hu Zhang, Chenggang Fang, XiaoDiao Huang
doaj   +1 more source

超声研齿的材料去除模型与试验

Jixie chuandong, 2010
The theory and method of ultrasonic lapping spiral bevel and hypoid gears are firstly purposed.The material removal mechanism of ultrasonic lapping gears specified as abrasives hammering to micro-cut,bouncing to impact and slurry cavitation is analyzed ...
魏冰阳, 杨琰, 杨建军, 邓效忠
doaj