Results 51 to 60 of about 9,187,308 (237)

Optimization of PWHT of Simulated HAZ Subzones in P91 Steel with Respect to Hardness and Impact Toughness

open access: yesMetals, 2020
Appropriate post weld heat treatment (PWHT) is usually obligatory when creep resistant steels are welded for thermal power plant components that operate at elevated temperatures for 30-40 years.
Gorazd Lojen, Tomaž Vuherer
doaj   +1 more source

Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel

open access: yesAdvanced Engineering Materials, EarlyView.
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe   +9 more
wiley   +1 more source

Buoyancy-driven crack propagation: the limit of large fracture toughness [PDF]

open access: yes, 2007
We study steady vertical propagation of a crack filled with buoyant viscous fluid through an elastic solid with large effective fracture toughness. For a crack fed by a constant flux Q, a non-dimensional fracture toughness K=Kc/(3μQm3/2)1/4 describes the
Roper, S.M.   +3 more
core   +1 more source

Influence of carbon content on microstructure and mechanical properties of Mn13Cr2 and Mn18Cr2 cast steels [PDF]

open access: yesChina Foundry, 2014
In this paper, a comparison study was carried out to investigate the influence of carbon content on the microstructure, hardness, and impact toughness of water-quenched Mn13Cr2 and Mn18Cr2 cast steels.
Lu Dingshan, Liu Zhongyi, Li Wei
doaj  

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

open access: yesAdvanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo   +15 more
wiley   +1 more source

Causes of scatter in high rate fracture testing of polymers [PDF]

open access: yes, 2013
A method based on the measurement of failure time is being developed by the European Structural Integrity Society to determine high rate fracture toughness of polymers.
Horsfall I.   +3 more
core   +1 more source

Impact Toughness Anisotropy of Hot-Rolled Ti-6Al-4V-0.5Ni-0.5Nb Alloy Sheet: Roles of Texture and Microstructure

open access: yesMetals
The α-phase microstructure and texture of a Ti-6Al-4V-0.5Ni-0.5Nb titanium alloy hot-rolled plate can easily lead to anisotropy in impact toughness. This study observed the microstructure and texture of the alloy plate on different planes, conducted ...
Bo Fu   +7 more
doaj   +1 more source

The influence of the vanadium content on the toughness and hardness of high-alloyed Cr-Mo steel

open access: yesZaštita Materijala, 2017
Characteristics of air hardening steel are high hardness and low impact toughness. In order to increase the impact toughness while retaining replace with the high hardness value numerous research added.
Ivica Čamagić   +2 more
doaj   +1 more source

Microstructural Evolution and In Situ Formation of TiB and TiC in Ti─5Al─2.5Sn Alloy Processed by Powder Metallurgy

open access: yesAdvanced Engineering Materials, EarlyView.
Accelerated in situ formation of TiB and TiC in Ti–5Al–2.5Sn–B4C is driven by transient liquid phase formation, which enhances particle reactions and microstructural evolution. This process increases hardness and establishes a coupled relationship between sintering temperature and reinforcement content, strongly influencing porosity in the resulting ...
Fernando. Y. Kojima, Juliano. Soyama
wiley   +1 more source

Analysis of impact properties of cemented carbide by electromagnetic coupled cryogenic treatment

open access: yesAIP Advances
Cemented carbide is often used as the pick-tip material for conical picks. The pick-tip often experiences premature failure due to insufficient toughness. This paper aims to improve the impact toughness of cemented carbide through electromagnetic coupled
Liang Tang, Zhi Chen, Xianguo Yan
doaj   +1 more source

Home - About - Disclaimer - Privacy