Results 31 to 40 of about 7,921,799 (295)
Influence of carbon content on microstructure and mechanical properties of Mn13Cr2 and Mn18Cr2 cast steels [PDF]
China Foundry, 2014 In this paper, a comparison study was carried out to investigate the influence of carbon content on the microstructure, hardness, and impact toughness of water-quenched Mn13Cr2 and Mn18Cr2 cast steels.
Lu Dingshan, Liu Zhongyi, Li Wei
doaj
Validation of low velocity impact modelling on different stacking sequences of CFRP laminates and influence of fibre failure [PDF]
, 2013 This paper presents a validation of low-velocity impact Finite Element (FE) modelling. Based on switching ply location of reference layup [02,452,902,-452]s T700GC/M21 laminated plates from Bouvet et al.
Bouvet, Christophe +2 more
core +1 more source
New Directions for Adult and Continuing Education, EarlyView.ABSTRACT Advancing artificial intelligence (AI) has transformed learning and work, yet higher education and professional development programs have not systematically equipped learners for AI‐prevalent environments. This lack of preparation creates uncertainty regarding control, responsibility, trust, and accountability.
Moon‐Heum Cho, Jerusalem Merkebu
wiley +1 more source
Journal of the Mechanical Behavior of Materials, 2020 Nowadays, ultra-high hard armor (UHA) steels are employed in armor tracked vehicle (ATV) construction because of their high hardness, high strength to weight ratio, and excellent toughness.
Balaguru V. +2 more
doaj +1 more source
Influence of loading rate, alkali fibre treatment and crystallinity on fracture toughness of random short hemp fibre reinforced polylactide bio-composites [PDF]
, 2011 Plane-strain fracture toughness (KIc) of random short hemp fibre reinforced polylactide (PLA) bio-composites was investigated along with the effect of loading rate, fibre treatment and PLA crystallinity.
Alan Fernyhough +7 more
core +1 more source
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
Journal of Materials Research and Technology, 2023 In this study, the multi-scale microstructures of bainitic steel were refined to different degrees by austempering below Ms (martensite start temperature). The influence of multi-scale microstructures and their boundaries on impact toughness was analyzed.
Kun Wang +6 more
doaj +1 more source
About the impact behavior of woven-ply carbon fiber-reinforced thermoplastic- and thermosetting-composites: A comparative study [PDF]
, 2013 This study is aimed at comparing the response of TS-based (epoxy) and TP-based (PPS or PEEK) laminates subjected to low velocity impacts. C-scan inspections showed that impact led to diamond-shaped damage resulting from different failure mechanisms ...
Vieille, Benoit +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.A simplified thermoplastic pultrusion model is developed to predict thermal fields in glass fiber/polyethylene terephthalate (GF/PET) composites with reduced computational cost. By combining effective material homogenization, validation against literature data, and Gaussian‐process‐based optimization, the study reveals how heating limits, pulling speed,
Elder Soares +3 more
wiley +1 more source
Investigation of improving wear performance of hypereutectic 15%Cr-2%Mo white irons [PDF]
China Foundry, 2010 This study aimed at optimizing impact toughness and abrasion wear resistance of 15%Cr-2%Mo hypereutectic abrasion-resistant white irons. The effects of dynamic solidification, niobium addition, combined action of them and heat treatment have been ...
R. Reda, A. Nofal, Kh. Ibrahim
doaj