Results 41 to 50 of about 484,366 (250)
EnergiesThe jet impingement cooling technique is regarded as one of the most effective enhanced heat transfer techniques with a single-phase medium. However, in order to facilitate manufacturing, impingement with a large number of smooth circular hole jets is ...
Liang Xu +5 more
doaj +1 more source
Wood‐Derived Nanocellulose‐Biocarbon Fresnel‐Zone Plate Lenses for Sub‐THz Frequency Applications
Advanced Materials Technologies, EarlyView.Wood‐derived nanocellulose and lignin‐based biocarbon were combined to fabricate fully bio‐based Fresnel zone plate (FZP) lenses for sub‐terahertz frequencies. These sustainable FZP lenses exhibit low dielectric loss and high directivity, achieving performance comparable to that of metallic references, and remain functional under environmental stress ...
Riikka Haataja +9 more
wiley +1 more source
Radiometric Constraints on the Timing, Tempo, and Effects of Large Igneous Province Emplacement
Geophysical Monograph Series, Page 27-82., 2021 Exploring the links between Large Igneous Provinces and dramatic environmental impact
An emerging consensus suggests that Large Igneous Provinces (LIPs) and Silicic LIPs (SLIPs) are a significant driver of dramatic global environmental and biological changes, including mass extinctions.
Jennifer Kasbohm +2 more
wiley +2 more sources
Heat exchange enhancement of jet impingement cooling with the novel humped-cone heat sink
Case Studies in Thermal Engineering, 2021 Jet impingement cooling technology is applicable to control temperature of devices, where very high heat flux is generated within a small area. This paper is about the improvement of the jet impingement cooling efficiency by the heat sink geometry ...
Marcin Froissart +3 more
doaj +1 more source
High Throughput Aerosol Jet Printing to Operationalize High Aspect Ratio Patterning
Advanced Materials Technologies, EarlyView.High‐throughput aerosol jet printing poses distinct limiting mechanisms to the printing process. These include rapidly changing ink chemistries, atomization instabilities, and liquid‐phase spreading. The combination of in‐line heating, process monitoring, and traditional optimization procedures enables rapid printing of high‐aspect‐ratio structures ...
Bella I. Guyll +4 more
wiley +1 more source
Recent Advances in Cooling Technology for the Leading Edge of Gas Turbine Blades
EnergiesAs the inlet temperature of the gas turbine exceeds the high temperature limit of the blade materials, efficient leading edge cooling technologies are crucial for the further development of gas turbines.
Shixing Zhu +3 more
doaj +1 more source
Propulsion and Power Research, 2015 It is known that the leading edge has the most critical heat transfer area of a gas turbine blade. The highest heat transfer rates on the airfoil can always be found on the stagnation region of the leading edge.
G. Lin +6 more
doaj +1 more source
Applied Sciences, 2023 A novel compound multi-jet impingement system for enhanced cooling of a flat surface by augmenting its area with cylindrical protrusions (CPs) equipped with coaxial guide vanes (CGVs) and reducing deflection of jets by crossflow has been developed for ...
Ahmet Hikmet Untuç, Salih Ozen Unverdi
doaj +1 more source
Advanced Materials Technologies, EarlyView.Multilayer aerosol jet printed components with a low‐loss, thermally stable dielectric are demonstrated using benzocyclobutene. Ink formulation and in‐line droplet evaporation control support high‐quality, versatile, and stable printing performance. A specialized measurement for low‐loss materials reveals promising microwave properties, which, combined
Md Ramjan Ali +3 more
wiley +1 more source
MATEC Web of Conferences, 2018 Multiple droplets are drops of water that continuously dropped onto a surface. Spray cooling is an application of the use of droplet on a cooling system. Spray cooling is usually used in a cooling system of electronic devices, and material quenching.
Riswanda Aria +4 more
doaj +1 more source