Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys
Advanced Engineering Materials, EarlyView.This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa +9 more
wiley +1 more source
Stability of a granular layer on an inclined "fakir plane" [PDF]
, 2012 We present here experimental results on the effect of a forest of cylinder obstacles (nails) on the stability of a granular layer over a rough incline, in a so-called "fakir plane" configuration.
Benito, Jesica +3 more
core +3 more sources
Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May +9 more
wiley +1 more source
STATIC OF ORTHODONTIC APPLIANCES WITH MOVABLE INCLINED PLANE FOR MESIAL BATE TREATMENT
Український стоматологічний альманах, 2018 Urgency of an issue. An orthodontic appliance with a movable inclined plane, which consists of a plastic base, vestibular arc, retaining clasps and inclined plane, connected with the base via two clubshaped springs (torsion springs) was proposed ...
P.S. Flis +4 more
doaj
Experimental and numerical studies of inclined cables: free and parametrically-forced vibrations [PDF]
, 2008 Because of few experimental studies in the inclined cable literature, this paper is aimed at experimental modelling and investigating the linear free and nonlinear forced vibrations of sagged inclined cables, by discussing the relevant outcomes in the ...
Alaggio, R., Rega, G., Srinil, N.
core
Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading
Advanced Engineering Materials, EarlyView.The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley +1 more source
(E)-3-Isopropyl-1-methyl-2,6-diphenylpiperidin-4-one O-nicotinoyl oxime
Acta Crystallographica Section E, 2014 In the title compound, C27H29N3O2, the piperidine ring exists in a chair conformation with an equatorial orientation of the phenyl and methyl substituents. The C—C=N bond angles are significantly different [119.1 (2) and 127.2 (2)°]. The phenyl rings are
T. Vinuchakkaravarthy +4 more
doaj +1 more source
Effect of interparticle forces on the fluidization of fine particles [PDF]
, 1969 Report studies elucidation and description of effect of interparticle forces on feasibility of gaseous fluidization of particles below 50 microns in diameter. Interparticle forces are determined by inclined-plane method.
Baerns, M. G., Ramaswami, D.
core +1 more source
Restoration of azimuthal symmetry of muon densities in extended air showers
, 2020 At ground level, the azimuthal distribution of muons in inclined Extensive Air Showers (EAS) is asymmetric, mainly due to geometric effects. Several EAS observables sensitive to the primary particle mass, are constructed after mapping the density of ...
Arsene, Nicusor +2 more
core +1 more source
Dependence of Spiral Galaxy Distribution on Viewing Angle in RC3 [PDF]
, 2000 The normalized inclination distributions are presented for the spiral galaxies in RC3. The results show that, except for the bin of $81^{\circ}$-$90^{\circ}$, in which the apparent minor isophotal diameters that are used to obtain the inclinations, are ...
Cheng-Gang Shu +13 more
core +2 more sources