Results 151 to 160 of about 31,144 (273)
International Journal for Numerical Methods in Fluids, Volume 98, Issue 4, Page 492-509, April 2026.This paper presents a finite element method for simulating highly viscoelastic flows of pure polymer melts using the Elastic Viscous Stress Splitting formulation. The method avoids higher‐order derivatives in the weak formulation by reformulating the convective term in the constitutive equation.
R. Ahmad, P. Zajac, S. Turek
wiley +1 more source
Pressurized Solid Oxide Electrolysis—Operational Strategies
Fuel Cells, Volume 26, Issue 2, April 2026.ABSTRACT Pressurized high‐temperature electrolysis is a promising pathway for high‐efficiency hydrogen production that enables direct compression and heat recovery opportunities not accessible to low‐temperature electrolysis. While laboratory testing is routinely conducted near atmospheric pressure, there is increasing interest in commercial deployment
Stephen Woodward +2 more
wiley +1 more source
Polymer Composites, Volume 47, Issue 5, Page 4102-4126, 10 March 2026.Comparison of experimental and model‐predicted erosion rates for carbon fibre‐reinforced polymer (CFRP) and glass fibre‐reinforced polymer (GFRP) under low‐velocity (2 m/s) and at varying angles and sand concentrations (0.0, 0.05, 0.4 g/L). The results demonstrate good agreement between experimental data and model predictions across different erosive ...
Ali Al‐Darraji +4 more
wiley +1 more source
Assessing the accuracy of the coupled-spherical-bubble approach for bubble pairs in an acoustic field. [PDF]
Ultrason SonochemNagy D, Hegedűs F.
europepmc +1 more source
Advanced Materials, Volume 38, Issue 13, 3 March 2026.Holographic microlithography enables the fabrication of fully connected 3D liquid crystalline structures in a single exposure. The process maintains precise control over the director orientation within the entire object, preventing local director distortions typically observed in sequential printing.
Lovish Gulati +8 more
wiley +1 more source
Ecosystem‐Centered Robot Design: Toward Ecoresorbable Sustainability Robots (ESRs)
Advanced Science, Volume 13, Issue 15, 13 March 2026.Robots exploring natural ecosystems can support monitoring and conservation, but must adopt ecosystem‐centered design to avoid pollution, waste, and damage. This review proposes guidelines for co‐designing ecoresorbable sustainability robots (ESRs), uniting materials, robotics, and ecological contexts in a single framework.
Tülin Yılmaz Nayır +4 more
wiley +1 more source
ANN-based analysis of MHD third-grade hybrid nanofluid flow over a thin needle with fuzzy volume fraction under nonlinear radiation and heat generation. [PDF]
Sci RepSiddique I +6 more
europepmc +1 more source
Advanced Science, Volume 13, Issue 16, 18 March 2026.A computationally designed, cobalt‐free maraging steel tailored for additive manufacturing achieves an ultra‐high tensile strength of 2.3 GPa with 5.7% elongation. This exceptional strength‐ductility synergy stems from high‐density core‐shell Ni3Ti/NiAl nanoprecipitates, a crack‐resistant composition, and a fine equiaxed grain structure enabled by ...
Hu Li +6 more
wiley +1 more source
Design and Validation of a Pressure-Driven Liquid Metering System with Heated PTFE Tubing for Laboratory Automation. [PDF]
Sensors (Basel)Baek J +5 more
europepmc +1 more source
Photothermal Transport for Guiding Nanoparticles Through the Vitreous Humor
Advanced Science, Volume 13, Issue 16, 18 March 2026.Nanosecond laser irradiation of the clinically approved dye indocyanine green (ICG) enables light‐guided nanoparticle transport within the vitreous humor. The combined use of ICG and pulsed laser illumination induces localized convection and thermophoresis, directing particles toward illuminated regions.
Léa Guerassimoff +9 more
wiley +1 more source