Results 21 to 30 of about 422,530 (222)
Hole Making of Inconel 718 Aerospace Alloy [PDF]
Acta Mechanica Slovaca, 2016 Different surface integrity parameters have become one of the major interest within aero engine components production in the aerospace industry. Hole making process of nickel based super alloy Inconel 718 consists of two machining operations, where drilling is applied to remove stock material and is followed by reaming to meet required quality as well ...
Marek Vrabeľ, Martin Eckstein
openaire +1 more source
Tool-life and wear mechanisms of CBN tools in machining of Inconel 718 [PDF]
, 2007 The demand for increasing productivity when machining heat resistant alloys has resulted in the use of new tool materials such as cubic boron nitride (CBN) or ceramics.
DESSOLY, Michel +4 more
core +1 more source
Impact of hydrogen on the high cycle fatigue behaviour of Inconel 718 in asymmetric push–pull mode at room temperature [PDF]
, 2015 The influence of hydrogen on the high cycle fatigue (HCF) behaviour of Inconel 718 has been studied at room temperature in asymmetric push–pull mode using an ultrasonic HCF test rig. Fatigue tests have been carried out in gaseous hydrogen (GH2) and in Ar
Fischer, B. +10 more
core +1 more source
Thermophysical properties of Inconel 718 alloy
Journal of Physics: Conference Series, 2019 Abstract The thermal diffusivity (a), linear thermal expansion coefficient (α), isobaric heat capacity (Cp ) and phase transition enthalpy (ΔH) of Inconel 718 superalloy were determined by laser flash method, dilatometric method and differential scanning calorimetry in the temperature range of 298–1375…1473 К.
A Sh Agazhanov +2 more
openaire +1 more source
Some features of anisothermal solid-state transformations in alloy 718 [PDF]
, 2010 This paper presents an attempt to use differential thermal analysis to study anisothermal precipitation of both the stable delta and the metastable gamma-second phases during cooling of alloy Inconel 718.
Niang, Aliou +2 more
core +1 more source
International Journal of Electrochemical Science, 2017 The electropolishing behavior of Inconel 718 alloy was studied with an alternating current (AC) impedance test at 25oC in perchloric-acetic mixed acids with different HClO4 contents.
Ching An Huang +2 more
doaj +1 more source
Degradation modes and tool wear mechanisms in finish and rough machining of Ti17 Titanium alloy under high-pressure water jet assistance [PDF]
, 2013 This article presents the results of an experimental study on the Ti17 titanium alloy, which was carried out to analyze tool wear and the degradation mechanisms of an uncoated tungsten carbide tool insert. Two machining conditions, roughing and finishing,
GERMAIN, Guénaël +3 more
core +1 more source
Future research directions in the machining of Inconel 718 [PDF]
, 2021 Inconel 718 is the most popular nickel-based superalloy, extensively used in aerospace, automotive and energy industries owing to its extraordinary thermomechanical properties.
De Bartolomeis, Andrea +4 more
core +1 more source
Aeronautical requirements for Inconel 718 alloy
IOP Conference Series: Materials Science and Engineering, 2017 The project goal is to present the requirements imposed by aviation components made from super alloys based on Nickel. A significant portion of fasteners, locking lugs, blade retainers and inserts are manufactured from Alloy 718. The thesis describes environmental factors (corrosion), conditions of external aggression (salt air, intense heat, heavy ...
C F Elefterie +3 more
openaire +1 more source
Cryogenic machining of the aeronautic alloy: Inconel 718
, 2021 Nickel-based alloys are widely used in the manufacture of aerospace engine components due to their excellent high-temperature thermo-mechanical properties and good corrosion resistance. However, machining these materials poses a number of challenges, mainly because they maintain their properties at high temperatures. Additional difficulties result from
openaire +3 more sources