Results 71 to 80 of about 164,491 (286)

Mechanical Properties of Microstructural Components of Inorganic Materials [PDF]

, 2013
Disertační práce se zabývá studiem strukturních a mechanických vlastností anorganických materiálů. Cílem je nalezení jednotlivých fází ve zkoumaném materiálu a hlavně lokalizace (mechanicky) nejslabšího místa, jeho ovlivnění a následně výroba materiálu o
Wasserbauer, Jaromír
core  

Hybrid Auxetic Architectures: Integrating Curvature‐Driven Design for Enhanced Mechanical Tunability and Structural Performance

Advanced Engineering Materials, EarlyView.
Curvature‐tuned auxetic lattices are designed, fabricated, and mechanically characterized to reveal how geometric curvature governs stretchability, stress redistribution, and Poisson's ratio evolution. Photoelastic experiments visualize stress pathways, while hyperelastic simulations quantify deformation mechanics.
Shuvodeep De, Giovanni Meli, Meysam Khalighian, Anahita Emami   +3 more
wiley   +1 more source

Mechanical properties of ultra-high pressure sintered sphene (CaTiSiO5) [PDF]

Processing and Application of Ceramics, 2016
The investigation of nano-mechanical properties of sphene sintered under ultra-high pressures in the order of 4 GPa is done using indentation techniques.
Eranezhuth Wasan Awin, Branko Matović, Jelena Maletaškić, Vladimir Urbanovich, Ravi Kumar   +4 more
doaj   +1 more source

Microstructural Evolution and Mechanical Performance of Plasma‐Assisted Hybrid Friction Stir Welded Dissimilar Aluminum–Copper Joints

Advanced Engineering Materials, EarlyView.
Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi, Pankaj Shrivastava, Ganesh Chouhan, Velaphi Msomi   +3 more
wiley   +1 more source

Evaluating the Wear of Polycrystalline Diamond Compact Drill Bit Cutters using Indentation and Scratch Tests

ARO-The Scientific Journal of Koya University, 2018
–Polycrystalline diamond compact (PDC) drill bits are widely used in oil and gas drilling. The wear of PDC cutters is a major problem during drilling. It leads to severe time losses which affect the overall drilling operation cost.
Rafid K. Abbas, Ali R. Hassanpour
doaj   +1 more source

Bayesian changepoint analysis for atomic force microscopy and soft material indentation

, 2008
Material indentation studies, in which a probe is brought into controlled physical contact with an experimental sample, have long been a primary means by which scientists characterize the mechanical properties of materials.
Bacon, Carlin, Chen, Chernoff, Choy, Costa, Costa, Crick, Dimitriadis, Elkin, Fearnhead, Ferreira, Geisse, Gouldstone, Hudson, Kala, Lai, Lieber, Lin, Lin, Lu, Menzefricke, Punskaya, Quandt, Radmacher, Robison, Rotsch, Smith, Smith, Stephens, Wolfe, Wong, Yue, Yuen, Zacks, Zellner   +35 more
core   +3 more sources

Nonlinear Elastic Material Property Estimation of Lower Extremity Residual Limb Tissues [PDF]

, 2003
The interface stresses between the residual limb and prosthetic socket have been studied to investigate prosthetic fit. Finite-element models of the residual limb-prosthetic socket interface facilitate investigation of the mechanical interface and may ...
Silver-Thorn, M. Barbara, Tönük, Ergin   +1 more
core   +2 more sources

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Modeling Density Waves and Circulations in Vertical Cross-Section in Adhesive Contacts

Computation
This work continues the study of the process of friction between a steel spherical indenter and a soft elastic elastomer previously published in our paper.
Aleksander E. Filippov, Iakov A. Lyashenko, Valentin L. Popov   +2 more
doaj   +1 more source

Mechanically Deposited Wear‐Resistant Amorphous Zr55Cu30Al10Ni5 Coatings

Advanced Engineering Materials, EarlyView.
Mechanically deposited from glassy ribbons, the Zr55Cu30Al10Ni5 amorphous coating formed a hard, continuous layer on AISI 1010 steel, tripling substrate hardness, lowering friction, and reducing wear. Despite its rough surface, it showed friction and wear behavior comparable to the crystalline alloy, highlighting its strong potential as a durable ...
Tales Ferreira, Pietro Cazelatto Bortolini, André Luiz Vidilli, Paulo Wilmar Barbosa Marques, Jéferson Aparecido Moreto, Claudio Shyinti Kiminami, Walter José Botta, Claudemiro Bolfarini, Guilherme Yuuki Koga   +8 more
wiley   +1 more source