Results 71 to 80 of about 19,950 (296)
Advanced Engineering Materials, EarlyView.Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver +9 more
wiley +1 more source
Crystals, 2017 Single-crystal sapphire (α-Al2O3) is a hard and brittle material. Due to its highly crystalline nature, the fracture behavior of sapphire is strongly related to its crystal structure, and understanding the effects of crystal structure on the crack ...
Ningchang Wang +3 more
doaj +1 more source
A Dislocation Perspective on Strength and Toughness in Ceramics
Advanced Engineering Materials, EarlyView.Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley +1 more source
Metals, 2020 Residual stresses, existed in engineering structures, could significantly influence the mechanical properties of structures. Accurate and non-destructive evaluation of the non-equibiaxial residual stresses in these structures is of great value for ...
Guangjian Peng +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
, 2017 Nanomechanical testing using depth sensing indentation (DSI) provides a straightforward solution for characterizing of mechanical properties (indentation hardness HIT, Young’s modulus EIT, indentation energy: total Wtotal, elastic Welast, plastic Wplast)
Burik Peter +3 more
core +2 more sources
Method to determine the optimal constitutive model from spherical indentation tests
Results in Physics, 2018 The limitation of current indentation theories was investigated and a method to determine the optimal constitutive model through spherical indentation tests was proposed.
Tairui Zhang, Shang Wang, Weiqiang Wang
doaj +1 more source
Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition
Advanced Engineering Materials, EarlyView.AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley +1 more source
Advanced Functional Materials, EarlyView.A gradient M/MOx (M = Sn, Cu, Cd) synergistic interphase was constructed on Al via a one‐step displacement reaction. This interphase leverages high aluminophilicity and ion‐buffering capability to accelerate desolvation, enhance Al3+ transport, and suppress side reactions, enabling ultrastable symmetric cell operation at 0.05 mA cm−2 for 1800 h with an
Shuang Cheng +7 more
wiley +1 more source
Effect of Heavy Ion Irradiation Dosage on the Hardness of SA508-IV Reactor Pressure Vessel Steel
Metals, 2017 Specimens of the SA508-IV reactor pressure vessel (RPV) steel, containing 3.26 wt. % Ni and just 0.041 wt. % Cu, were irradiated at 290 °C to different displacement per atom (dpa) with 3.5 MeV Fe ions (Fe2+).
Xue Bai +4 more
doaj +1 more source