Assessment of field rolling resistance of manual wheelchairs [PDF]
, 2012 This article proposes a simple and convenient method for assessing the subject-specific rolling resistance acting on a manual wheelchair, which could be used during the provision of clinical service.
BASCOU, Joseph +5 more
core +1 more source
A method for the field assessment of rolling resistance properties of manual wheelchairs, Computer Methods in Biomechanics and Biomedical Engineering [PDF]
, 2012 This article presents an examination and validation of a method to measure the field deceleration of a manual wheelchair (MWC) and to calculate the rolling resistances properties of the front and rear wheels.
Hélène Pillet +11 more
core +1 more source
Analytical substantiation of constructive parameters of rotating field board of plow’s body [PDF]
E3S Web of Conferences, 2019 The article shows importance of use of dump plowing for formation and maintenance of soil structure and pest control and diseases of cultivated plants. A significant drawback of plowing process is indicated, which is its high energy intensity.
Konovalov Vladimir +2 more
doaj +1 more source
Permanent indentation characterization for low-velocity impact modelling using three-point bending test [PDF]
, 2014 This paper deals with the origin of permanent indentation in composite laminates subjected to low-velocity impact. The three-point bending test is used to exhibit a non-closure of matrix crack which is assumed as a cause of permanent indentation ...
Bouvet, Christophe +3 more
core +1 more source
Evaluation of rolling contact fatigue behaviour of nitrided SCM435 in a contaminated lubrication
Nihon Kikai Gakkai ronbunshu, 2020 In this study, the rolling contact fatigue (RCF) life of nitrided Cr-Mo steel, which has three types of different nitride compound layers, was investigated under contaminated lubrication.
Tomoya SADAMORI +3 more
doaj +1 more source
Investigation into the effect of common factors on rolling resistance of belt conveyor
Advances in Mechanical Engineering, 2015 Since indentation rolling resistance accounts for the major part of total resistance of belt conveyor, it is important to compute it using a proper method during the design and application study of the belt conveyor.
Lu Yan, Lin Fu-Yan, Yu Xin-Bo
doaj +1 more source
ANALYSIS OF CONTACT OF A RIGID SPHERE AGAINST A DEFORMABLE FLAT
Acta Metallurgica Slovaca, 2015 In the paper the strain hardening effect on the contact of a rigid ball and elastic-plastic flat is considered using experiments and finite element method. The experiments were carried out for DC04 steel sheet metal.
Tomasz Trzepieciński +4 more
doaj +1 more source
Nihon Kikai Gakkai ronbunshu, 2017 In this study, the effect of shot peening on rolling contact fatigue life of bearing steel was investigated under contaminated lubrication. Shot peening was carried out on bearing steel SUJ2 specimens. Peened specimens were polished to remove the dimples
Tomoya SADAMORI +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
An investigation of nanoindentation tests on the single crystal copper thin film via an AFM and MD simulation [PDF]
, 2007 Nanoindentation tests performed in an atomic force microscope have been utilized to directly measure the mechanical properties of single crystal metal thin films fabricated by the vacuum vapor deposition technique. Nanoindentation tests were conducted at
Liang, Y, Cheng, K, Huo, D
core +6 more sources