Results 71 to 80 of about 12,577,788 (269)
Anisotropic Yield Criterion of Rolled AZ31 Magnesium Alloy via Nanoindentation
Applied Sciences, 2020 In this paper, the anisotropic mechanical properties of rolled AZ31 magnesium alloys are investigated using nanoindentation tests at room temperature.
Zai Wang +5 more
doaj +1 more source
High‐Resolution Corrosion Fingerprinting of Alloy Libraries via Microdroplet Spectroelectrochemistry
Advanced Engineering Materials, EarlyView.Ionic‐liquid microdroplet spectroelectrochemistry enables stable, localized electrochemical measurements over extended timescales. By coupling impedance spectroscopy, wetting analysis, finite‐element simulations, and operando Raman spectroscopy, it disentangles geometrical and electrochemical effects, opening new opportunities for rapid corrosion ...
Ekaterina Kurchavova +3 more
wiley +1 more source
Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys
Advanced Engineering Materials, EarlyView.An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi +5 more
wiley +1 more source
High temperature indentation of WC/Co hardmetals
, 2013 WC/Co is the material of choice for most high wear applications such as hot forming operations, drilling, cutting, machining and wire drawing due to its superior wear properties.
Zunega, Jonee Christine
core +1 more source
Advanced Engineering Materials, EarlyView.Residual adhesive after electrode loading in adhesive‐assisted resistance spot welding is quantified through a traceable experimental‐to‐digital workflow. Chromatic confocal topography provides calibrated surface‐height data, while OpenCV detects the electrode imprint and integrates adhesive height into comparable volume metrics.
Sung‐Min Wi, Jiangdong Zhao
wiley +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study explores the discrepancies between bulk mechanics and spatial mapping in a tissue‐mimetic hydrogel model. Microplastic particles create localized stiff mechanical microenvironments that are detectable by cellular‐scale nanoindentation but leave bulk properties unchanged as measured by rheology.
Ahron T. Verschleisser +3 more
wiley +1 more source
Journal of Advanced Ceramics, 2019 The nanoindentation loading curves measured on fused silica were analyzed based on the theoretical relationship derived by Malzbender et al. (J Mater Res 2000, 15: 1209–1212).
Yunbiao Duan, Danyu Jiang, Jin Hu
doaj +1 more source
Materials & Design, 2018 The paper presents a comparative study of different nanoindentation methods as applied to the ferritic/martensitic steels T91 and Eurofer97, here investigated in the non-irradiated reference state, but envisaged as structural materials for nuclear ...
Ana Ruiz-Moreno, Peter Hähner
doaj +1 more source
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source