Results 71 to 80 of about 25,681 (257)

Recovery of transversely-isotropic elastic material parameters in induction motor rotors

Journal of Mathematics in Industry
We propose numerical algorithms for recovering parameters in eigenvalue problems for linear elasticity of transversely isotropic materials. Specifically, the algorithms are used to recover the elastic constants of a rotor core.
Hanz M. Cheng, Tapio Helin, Ville-Petteri Manninen, Timo Holopainen, Juha Jokinen, Samu Sorvari, Andreas Rupp   +6 more
doaj   +1 more source

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions

Advanced Engineering Materials, EarlyView.
This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi, Kimiya Tajik, Harvey Shaw, Matti Isakov, Sami Pajunen, Lauri Rautkari   +5 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Experimental and Numerical Modal Analysis of Composite Sandwich Structures Using Surfboards as Model Systems

Advanced Engineering Materials, EarlyView.
This article presents an experimental and numerical modal investigation of composite sandwich structures using surfboards as model systems. By comparing different core materials and reinforcement strategies, the study demonstrates how local stiffeners influence vibrational response and introduce characteristic modal features, highlighting modal ...
Brett Connellan, Luca Lomazzi, Mathis Mercier, Kara Stark, Marc in het Panhuis   +4 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source

Development of Induction Heating Simulator for the Bending of Plates with Primary Curvature

Journal of the Society of Naval Architects of Korea, 2005
The induction heating is more efficient for a plate bending because of its easy operation and control of working parameters compared with the heating by torch. In this study, a more efficient method was proposed for the prediction of plate bending. The existing analysis method using the axi-symmetric coil model could not handle the varying temperature ...
openaire   +2 more sources

From Food to Power: Hydrogel Thermoelectrics for Ingestible Electronics

Advanced Functional Materials, EarlyView.
We introduce a fully edible thermoelectric–electrochromic platform that harvests heat from food and converts it into a visible color change. N‐type and p‐type hydrogel thermoelectric generators connected in series power anthocyanin‐based electrochromic displays, demonstrating the feasibility of safe, biodegradable, ingestible systems for on‐food ...
Antonia Georgopoulou, Bokeon Kwak, Dario Floreano, Esther Amstad   +3 more
wiley   +1 more source