Results 131 to 140 of about 2,213 (254)

Additive Manufacturing of Discontinuous Carbon Fibre-Reinforced Polymer (CFRP): A Study on Parametric Optimization Towards Mechanical Properties. [PDF]

Polymers (Basel)
Degnah A, Kurdi A, Pramanik A, Basak AK.
europepmc   +1 more source

New Results From the Pre‐Pottery Neolithic Site of Al Uyaynah, Tabuk, in Northwestern Saudi Arabia

Arabian Archaeology and Epigraphy, Volume 37, Issue 1, Page 182-206, November 2026.
ABSTRACT Al Uyaynah is a low sandstone mound on an alluvial plain, long known for its extensive surface remains of stone‐built circular and rectangular structures. Following test excavations in 2012, more detailed excavation was undertaken in 2016 within one of the largest rectangular stone structures.
Khalid Alasmari, Stephanie F. Piper, Kirsten Grothe, W. Derek Hamilton, Delphine Joly, Penny Bickle, Geoff Bailey   +6 more
wiley   +1 more source

ForamJ - A tool for the reproducible, semi-automated analysis of foraminifera micro computed tomography datasets. [PDF]

Sci Rep
Trend J, Borges FA, Babila TL.
europepmc   +1 more source

Infill shear walls in precast concrete frames

, 2018
The present work presents a study on structural masonry built inside precast concrete frames dimensioned as part of the system of bracing of buildings, defining this type of element as Infill Shear Wall. Identified the main constructive details of the masonry infill walls that influence the behavior of the precast frame against the horizontal actions ...
Medeiros, Wallison Angelim, Parsekian, Guilherme Aris   +1 more
openaire   +1 more source

Prediction of Tensile Behavior in Additively Manufactured Polymer Matrix Composites via an Integrated Analytical Approach

Polymer Composites, Volume 47, Issue 19, Page 17501-17513, 10 October 2026.
Integrated analytical framework for tensile response of additively manufactured polymer composites, supported by experimental validation. ABSTRACT Additive manufacturing (AM) enables innovative product development through its material versatility and design freedom, further enhanced by advanced materials such as composites.
Ozgur Poyraz, Abas Abasov
wiley   +1 more source

A multicentre audit of the geometric accuracy and water equivalence of 3D printed thermoplastic objects for use in radiotherapy. [PDF]

Phys Imaging Radiat Oncol
Jones MR, Woolliams PD, Bolt MA, McLaughlin O, Boutros M, Wright T, Jenkins R, Tonino A, Milliken F, Bentley N, Sands GD, Burnley JCL, Doolan PJ, McQuaid D, Budgell GJ, Adams EJ, McGarry CK, Clark CH.   +17 more
europepmc   +1 more source

Verifying calculated dose to the breast in stereotactic radiotherapy: A practical phantom‐based method

Journal of Applied Clinical Medical Physics, Volume 27, Issue 10, October 2026.
Abstract Background Reference dosimetry for the GammaPod breast radiosurgery device is determined in a polymethyl methacrylate (PMMA) phantom, while the clinical dose calculations assume the patient's breast has the atomic composition of water with a density (∼0.935 g/cm3).
Stewart J. Becker, Ryan E. Smith, Wesley S. Culberson, Kurt E. Stump, Baoshe Zhang, Jie Ding, Sina Mossahebi, Dennis Herschbach, Elizabeth M. Nichols   +8 more
wiley   +1 more source

Numerical investigation of the composite mechanical behavior of grouted rock members with rough fractures. [PDF]

Sci Rep
Zhang E, Li Y, Liu M, Liu L, Jia Q.
europepmc   +1 more source

Evaluation of testicular shielding effectiveness for surface and internal photon dose using a 3D‐printed scrotal phantom

Journal of Applied Clinical Medical Physics, Volume 27, Issue 10, October 2026.
Abstract Background Testicular shielding has long been used to reduce testicular dose during radiation treatment. However, quantitative evaluations of the effectiveness of such shielding in the literature vary substantially. Purpose In this study, the dose reduction expected at both the testicular skin surface and the inside of the testes was evaluated
Joseph Speth, Josh Kilian‐Meneghin, Salma K. Jabbour, Yin Zhang, Xiao Wang, Zhenyu Xiong, Ke Nie, Ning J. Yue, Xinxin Zhang   +8 more
wiley   +1 more source

Acoustic Absorption in 3D-Printed PLA Biocomposite Models: Influence of Grid, Trihexagonal, and Gyroid Infills and Biomass Reinforcement. [PDF]

ACS Appl Eng Mater
Tayari F, Silva R, Brilhante T, Cardoso I, Pinto P, Freitas V, Ribeiro R, Ferreira A, Gama N.   +8 more
europepmc   +1 more source