Results 91 to 100 of about 2,272,899 (317)

Injectivity And Annihilators

open access: yesDemonstratio Mathematica, 1990
The paper starts off with a characterization of the known concept of a biregular ring in terms of the complement left annihilator of a semiprime ring. A ring \(A\) is said to be a \(LIS\) ring if for any two right ideals \(I\), \(J\) of \(A\), the equality \(\ell(I\cap J)=\ell(I)+\ell(J)\) holds.
openaire   +2 more sources

Large Section Ceramic Injection Moulding

open access: yes, 2000
PhDCeramic injection moulding is already established as a production technique for complex shaped ceramic components. However the process is limited to thin section mouldings generally not exceeding a wall thickness of 10 mm.
Krug, S., Krug, Steffen
core  

Intracameral Injection of Bevacizumab for the Treatment of Neovascular Glaucoma [PDF]

open access: yes, 2011
Purpose: To assess the duration of the effect of intracameral bevacizumab in patients presenting with rubeosis iridis and neovascular glaucoma (NVG). Methods: Retrospective analysis of 24 consecutive eyes of 24 patients with decompensated NVG (> 21 mm Hg)
Haritoglou, Christos   +7 more
core   +1 more source

NEUROVACINIA WITH TYPHUS IN THE WORKS OF М. М. TZEKHOWITZER (REVIEW) [PDF]

open access: yesAnnals of Mechnikov's Institute, 2013
The article describes the work priorities M. M.Tzekhnowitzer. Describes the production of various types neurovaccinia. Characterized by immunization of animals living typhous neyrovirusom.
Moiseyenko T.N.
doaj  

FLUID FLOW MODEL BASED ON THE ANALYSIS OF WATER INJECTION DATA IN THE TURONIAN RESERVOIR OF THE LIAWENDA FIELD, OFFSHORE COASTAL BASIN OF D.R. CONGO [PDF]

open access: yesRomanian Journal of Petroleum & Gas Technology
Arranged the hydrocarbons in an oil reservoir require several techniques for their exploitation. The Liawenda field, discovered in December 1971 following the drilling of the Liawenda-01 exploration well, has a total of 186 wells with an annual ...
Munene Asidi Djonive   +8 more
doaj   +1 more source

PARP inhibitors induce a senescence phenotype in non‐small cell lung carcinoma cell lines

open access: yesFEBS Open Bio, EarlyView.
Talazoparib is the most potent inducer of senescence among different PARP1 inhibitors in human NSCLC cells. In the absence of PARP, no senescence phenotype was observed, demonstrating that PARP1 is necessary for the induction of senescence by this inhibitor.
Camille Huart   +7 more
wiley   +1 more source

EFFECT OF SHOCK WAVE THERAPYVERSUS CORTICOSTEROID INJECTION IN MANAGEMENT OFKNEE OSTEOARTHRITIS

open access: yesInternational Journal of Physiotherapy, 2016
Background: knee Osteoarthritis is the most common cause of musculoskeletal pain and disability. Shockwaves have been used as an alternative treatment for musculoskeletal disorders; intra-articular injection of steroid is a common treatment for ...
Ahmed Ebrahim Elerian   +2 more
doaj   +1 more source

Erythropoietin modulates hepatic inflammation, glucose homeostasis, and soluble epoxide hydrolase and epoxides in high‐fat diet‐induced obese mice

open access: yesFEBS Open Bio, EarlyView.
Erythropoietin administration suppresses hepatic soluble epoxide hydrolase (sEH) expression, leading to increased CYP‐derived epoxides. This is associated with a shift in hepatic macrophage polarization characterized by reduced M1 markers and increased M2 markers, along with reduced hepatic inflammation, suppressed hepatic lipogenesis, and attenuated ...
Takeshi Goda   +12 more
wiley   +1 more source

The Application of Commercial Injection Molding Software to Micro-Component Design and Process Development

open access: yes, 2013
The use of software developed for the simulation of injection molding is evaluated through a case study of a micro-injection molded micro-pump component.
Freiheit, Theodor I.   +2 more
core  

Analysis of rheological behaviour of titanium feedstocks formulated with a water-soluble binder system for powder injection moulding

open access: yes, 2014
Binder selection and formulation are critical in powder injection moulding. Binders play a key role in controlling the rheological properties of a feedstock and influence whether the resulting feedstock can be successfully injection moulded, debound and ...
Pickering, Kim L.   +3 more
core   +1 more source

Home - About - Disclaimer - Privacy