Results 11 to 20 of about 10,777 (200)
Archives of Foundry Engineering, 2018 In sand casting, Fused Deposition Modeling (FDM) printing by using Poly Lactic Acid (PLA) filament is one of the innovative foundry technologies being adopted to substitute traditional pattern making. Several literatures have reported the influence of process parameters such as raster angle and print speed on some mechanical properties of FDM-printed ...
Anakhu, Peter I. +6 more
openaire +1 more source
Preliminary Research on Granulation Process of Dust Waste from Reclamation Process of Moulding Sands with Furan Resin [PDF]
, 2012 The results of investigations of the granulation process of foundry dusts generated in the dry mechanical reclamation process of usedsands, where furan resins were binders are presented in the paper.
J. Dańko, J. Kamińska
core +6 more sources
The Design of Cast Technological Equipment for Heat Treatment Furnaces
Archives of Foundry Engineering, 2017 Various examples of the design of cast elements of the equipment used in furnaces for the heat treatment of machine parts are given. Shortcomings in their performance are indicated.
Drotlew A., Piekarski B., Słowik J.
doaj +1 more source
The use of scanning contactless conductivity detection for the characterisation of stationary phases in micro-fluidic chips [PDF]
, 2010 The use of scanning capacitively coupled contactless conductivity detection for the evaluation of the structural homogeneity and density of both packed and monolithic stationary phases in microfluidic chips is presented here for the first ...
Brett Paull +19 more
core +1 more source
The Flexibility of Pusher Furnace Grate
Archives of Foundry Engineering, 2016 The lifetime of guide grates in pusher furnaces for heat treatment could be increased by raising the flexibility of their structure through, for example, the replacement of straight ribs, parallel to the direction of grate movement, with more flexible ...
Słowik J.A., Drotlew A., Piekarski B.
doaj +1 more source
Analysis of Defects in Castings Cast by Rheocasting Method SEED
Archives of Foundry Engineering, 2016 The paper analyses specific defects of castings produced by semi-solid casting process, especially rheocasting method SEED, which uses mechanical swirling for reaching proper structure in semisolid state with high content of solid fraction.
Bryksi Stunova B., Bryksi V.
doaj +1 more source
Analysis of Crystallization Process of Intensive Cooled AlSi20CuNiCoMg Alloy
Archives of Foundry Engineering, 2017 The work is a continuation of research concerning the influence of intensive cooling of permanent mold in order to increase the casting efficiency of aluminium alloys using the multipoint water mist cooling system.
Władysiak R. +3 more
doaj +1 more source
Mechanical Stresses Induced by Compression in Castings of the Load-carrying Grate
Archives of Foundry Engineering, 2016 The main aim of this study was to examine the compression-induced state of stress arising in castings of the guide grates during operation in pusher-type furnaces for heat treatment. The effect of grate compression is caused by its forced movement in the
Słowik J., Drotlew A., Piekarski B.
doaj +1 more source
Technologies for trapped-ion quantum information systems [PDF]
, 2016 Scaling-up from prototype systems to dense arrays of ions on chip, or vast networks of ions connected by photonic channels, will require developing entirely new technologies that combine miniaturized ion trapping systems with devices to capture, transmit
Bylinskii, Alexei +5 more
core +2 more sources
The Influence of Home Scrap on Mechanical Properties of MgAl9Zn1 Alloy Castings
Archives of Foundry Engineering, 2017 The work presents the results of examinations concerning the influence of various amounts of home scrap additions on the properties of castings made of MgAl9Zn1 alloy. The fraction of home scrap in the metal charge ranged from 0 to 100%.
Konopka Z. +3 more
doaj +1 more source