Results 21 to 30 of about 567 (167)
Archives of Foundry Engineering, 2017 This paper presents the impact of microwave penetration depth on the process of heating the moulding sand with sodium silicate. For each material it is affected by: the wavelength in vacuum and the real and imaginary components of the relative complex ...
Nowak D.
doaj +1 more source
Archives of Foundry Engineering, 2015 The paper presents the results of basic research on the influence of the properties of sand grains on electrical properties of water glass moulding sands.
Opyd B., Granat K.
doaj +1 more source
New Materials in the Production of Moulding and Core Sands
Archives of Foundry Engineering, 2015 The article shows the influence of environment requirements on changes in different foundry moulding sands technologies such as cold box, self-hardening moulding sands and green sands.
Dobosz St. M. +2 more
doaj +1 more source
The Influence of the Mould Filling Conditions on the Quality of Castings Made of EN AC-44000 Alloy
Archives of Foundry Engineering, 2014 The work deals with the influence of change in the filling conditions of the ceramic moulds with plaster binder on the presence of gaseous porosity and the microstructure of the achieved test castings with graded wall thickness.
Nadolski M. +3 more
doaj +1 more source
The Aging Time Effects of the Pre-expanded Polystyrene on the Patterns Mechanical Properties
Archives of Foundry Engineering, 2015 The aging granulate is to activate the blowing agent during the manufacturing process to granulate models can re-expand and shape the model of well-sintered granules, smooth surface and a suitable mechanical strength.
Buczkowska K., Pacyniak T.
doaj +1 more source
Advanced Functional Materials, EarlyView.An all‐in‐one analog AI accelerator is presented, enabling on‐chip training, weight retention, and long‐term inference acceleration. It leverages a BEOL‐integrated CMO/HfOx ReRAM array with low‐voltage operation (<1.5 V), multi‐bit capability over 32 states, low programming noise (10 nS), and near‐ideal weight transfer.
Donato Francesco Falcone +11 more
wiley +1 more source
Integration of Low‐Voltage Nanoscale MoS2 Memristors on CMOS Microchips
Advanced Functional Materials, EarlyView.This article presents the first monolithic integration of nanoscale MoS2‐based memristors into the back‐end‐of‐line of foundry‐fabricated CMOS microchips in a one‐transistor‐one‐resistor (1T1R) architecture. The MoS2‐based 1T1R cells exhibit forming‐free, nonvolatile resistive switching with ultra‐low operating voltages, low cycle‐to‐cycle variability ...
Jimin Lee +16 more
wiley +1 more source
Archives of Foundry Engineering, 2016 The work is a continuation of research concerning the influence of intensive cooling of permanent mold in order to increase the casting efficiency of aluminium alloys using the multipoint water mist cooling system.
Władysiak R., Kozuń A., Pacyniak T.
doaj +1 more source
Ferroelectric Quantum Dots for Retinomorphic In‐Sensor Computing
Advanced Materials, EarlyView.This work has provided a protocol for fabricating retinomorphic phototransistors by integrating ferroelectric ligands with quantum dots. The resulting device combines ferroelectricity, optical responsiveness, and low‐power operation to enable adaptive signal amplification and high recognition accuracy under low‐light conditions, while supporting ...
Tingyu Long +26 more
wiley +1 more source
Archives of Foundry Engineering, 2014 Extremely intense development of civilization requires from foundry casting technologies very high quality and not expensive castings. In the foundries, there are many treatments that allow increasing of the final properties of produced castings such as ...
Karwiński A. +4 more
doaj +1 more source