Results 101 to 110 of about 411,092 (298)

Integrating Smart Ceiling Fans and Communicating Thermostats to Provide Energy-Efficient Comfort [PDF]

open access: yes, 2020
The project goal was to identify and test the integration of smart ceiling fans and communicating thermostats. These highly efficient ceiling fans use as much power as an LED light bulb and have onboard temperature and occupancy sensors for automatic ...
Arens, Edward   +12 more
core  

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

open access: yesAdvanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek   +5 more
wiley   +1 more source

Practical Use of Cloud Systems in Project Management [PDF]

open access: yes, 2015
V této bakalářské práci se zaměříme na popis cloudových systémů a jejich využití v projektovém plánování neziskové organizace. První část této práce se zabývá teoretickým úvodem do cloudových systémů.
Poustecký, Ondřej
core  

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

open access: yesAdvanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann   +3 more
wiley   +1 more source

Dynamic Testing of Cold Gas Sprayed Bipolar Plates–Porous Transport Layer Coating System in Proton Exchange Membrane Water Electrolysis

open access: yesAdvanced Engineering Materials, EarlyView.
Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin   +5 more
wiley   +1 more source

Bias Estimation for Evaluation of ATC surveillance systems [PDF]

open access: yes, 2009
This paper describes an off-line bias estimation and correction system for air traffic control related sensors, used in a newly developed Eurocontrol tool for the assessment of ATC surveillance systems.
Bernardos Barbolla, Ana M.   +4 more
core  

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

open access: yesAdvanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa   +9 more
wiley   +1 more source

Estimating the Influence of Improper Workplace Environment on Human Error: Posterior Predictive Analysis

open access: yesAdvances in Civil Engineering, 2018
A model for identifying, analyzing, and quantifying the mechanisms for the influence of improper workplace environment on human error in elevator installation is proposed in this study.
Pin-Chao Liao   +4 more
doaj   +1 more source

Towards Defect Phase Diagrams: From Research Data Management to Automated Workflows

open access: yesAdvanced Engineering Materials, EarlyView.
A research data management infrastructure is presented for the systematic integration of heterogeneous experimental and simulation data required for defect phase diagrams. The approach combines openBIS with a companion application for large‐object storage, automated metadata extraction, provenance tracking and federated data access, thereby supporting ...
Khalil Rejiba   +5 more
wiley   +1 more source

An Approach to Determine Installation Errors of Spiral Bevel Gears

open access: yesJournal of Mechanical Engineering, 2012
A positional parametric analysis of contact pattern is put forward,which can be used for determining the variation range of installation errors of spiral bevel gears.For forming the tooth surfaces of spiral bevel gears,manufacture parameters are designed based on local synthesis to meet design specifications.The pinion drive torque is calculated with ...
openaire   +1 more source

Home - About - Disclaimer - Privacy