Results 41 to 50 of about 37,322 (294)
Remote Sensing, 2021 Frequency modulation continuous wave (FMCW) Lidar inevitably suffers from vibration and nonlinear frequency modulation, which influences the ranging and imaging results.
Rongrong Wang +5 more
doaj +1 more source
Leak detection using instantaneous frequency analysis [PDF]
, 2012 Leaking pipes are a primary concern for water utilities around the globe as they compose a major portion of losses. Contemporary interest surrounding leaks is well documented and there is a proliferation of leak detection techniques. Although the reasons
M. F., Ghazali, ghazali, mohd fairusham
core
Annals of Clinical and Translational Neurology, EarlyView.ABSTRACT Background X‐linked adrenoleukodystrophy (X‐ALD) is a neurometabolic disorder caused by pathogenic variants in ABCD1, leading to slowly progressive spinal cord disease in nearly all affected men. Sensitive biomarkers to quantify disease severity and predict progression are needed for clinical care and trial design.
Eda G. Kabak +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Measuring of plasma’s velocity in electrodynamic railgun using high-frequency method
MATEC Web of Conferences, 2018 A method is proposed for measuring the velocity of a moving plasma in an electrodynamic railgun in the part of internal ballistics. The achieved result is to provide a measurement of instantaneous velocity and an increase of the safety level for ...
Kirievskiy Vladimir V. +1 more
doaj +1 more source
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source
Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading
Advanced Engineering Materials, EarlyView.The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley +1 more source
Frequency Measurement of Dynamic Stress in Polarization Maintaining Fibers
IEEE Photonics Journal, 2018 Up to now, the distributed polarization coupling (DPC) measurement system based on white light interferometry (WLI) has been mainly studied for static and quasi-static measurement.
Hongxia Zhang +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source