Results 171 to 180 of about 1,093,914 (301)

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Intensive Care Unit [PDF]

, 2008
奥寺 敬, 小池 勤, 澁谷 伸子
core   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Clinical and Imaging Predictors of Hematoma Expansion in Spontaneous Intracerebral Hemorrhage: Development of a Prognostic Model

Risk Management and Healthcare Policy
Yi-Guang Mao,1,* Jia-Yu Chen,2,* Man-Li Wang,3 Ying-Jun Ma,1 Chen Jiang1 1Department of Neurosurgery Intensive Care Unit, the Affiliated Wuxi People’s Hospital of Nanjing Medical University,Wuxi Medical Center,Nanjing Medical University ...
Mao YG, Chen JY, Wang ML, Ma YJ, Jiang C
doaj  

Intensive Care Unit [PDF]

, 2013
吉岡 伊作, 奥寺 敬, 峠 正義, 澁谷 伸子   +3 more
core   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

ASUHAN KEPERAWATAN PADA PASIEN POST KRANIOTOMI ATAS INDIKASI EPIDURAL HEMATOMA DAN GAGAL NAFAS DENGAN PENERAPAN PERAWATAN RESTRAIN UNTUK PENCEGAHAN KOMPLIKASI NEUROVASKULER DI INTENSIVE CARE UNIT (ICU) RSUP DR. M.DJAMIL PADANG TAHUN 2019 [PDF]

, 2019
UlfaIla'ika Liasanil
openalex  

Delineation Of Common Source Foci Requisite For Epidemiology And Environmental Control In Intensive Care Units.

, 1970
Lorraine Ann Renkowski
openalex   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

NURSES’ AUTONOMY IN INTERACTING WITH RELATIVES THROUGH DIARY WRITING IN THE INTENSIVE CARE UNIT; AN EXPLORATIVE MIXED METHODS STUDY

Margo M. C. van Mol
openalex   +1 more source