Results 141 to 150 of about 16,527,400 (269)

Simulation‐Based Analysis of Insert Pull‐Out in Nickel‐Polyurethane Hybrid Foams Using CT‐Derived Geometries

Advanced Engineering Materials, EarlyView.
CT‐based finite element simulations combined with in situ X‐ray computed tomography are used to analyze insert pull‐out in nickel‐coated polymer foams. Despite variations in material parameters, deformation consistently concentrates within a narrow annular region around the insert.
Yannik Bautz, Jonas Fell, Hendrik Jost, Stefan Diebels, Hans‐Georg Herrmann   +4 more
wiley   +1 more source

Phylogenetic inference under the balanced minimum evolution criterion via semidefinite programming. [PDF]

Bioinformatics
Skums P.
europepmc   +1 more source

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

Enhanced electrical conductivity at Fe₃O₄ grain boundaries. [PDF]

Sci Adv
Yao T, Gao C, Sun Z, Tao A, Jiang Y, Yang Z, Ma XL, Ye H, Chen C.   +8 more
europepmc   +1 more source

Interior Point Method

Journal of Japan Society for Fuzzy Theory and Systems, 1996
openaire   +2 more sources

Development of Interior-Point Methods

, 2000
During the last fifteen years we have witnessed an explosive development in the area of optimization theory due to the introduction and development of interior-point methods.
Lesaja, Goran
core  

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Prey-predator dynamics with additional food and Holling type-III response: application to Bemisia tabaci. [PDF]

Sci Rep
Prakash DB, Chaitanya C, Vamsi DKK, Aloqaily A, Mlaiki N.   +4 more
europepmc   +1 more source

Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses

Advanced Engineering Materials, EarlyView.
Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk, Elisabeth Keck, Alberto López‐Grande, Delia S. Brauer, Tobias Fey   +4 more
wiley   +1 more source

Research on the Interfacial Properties of AlSb Thin Films with Air Molecules. [PDF]

Nanomaterials (Basel)
Wang Y, Zhou P, Deng X, Cai F, Ren H, Jiang W, Zhao F, Song H, Yan Q, Zhang Y.   +9 more
europepmc   +1 more source