Results 111 to 120 of about 175,535 (378)
Advanced Healthcare Materials, EarlyView.Coatings of titanium‐gold are grown in nitrogen and oxygen environments via magnetron sputtering to simultaneously enhance their biotribological and antibacterial properties. The coatings are highly crystalline with superhard scratch‐resistant surfaces and wear rates 20 times lower than the bare Ti‐6Al‐4V substrate.
Cecil Cherian Lukose +11 more
wiley +1 more source
Ti6Al4V‐Bioglass‐Copper Composites for Load‐Bearing Implants
Advanced Healthcare Materials, EarlyView.We have designed and manufactured a novel Ti64‐based composite by adding 45S5 bioglass (BG) and copper (Cu). Adding BG on titanium improves wear resistance and biocompatibility, whereas Cu addition improves mechanical strength while providing inherent lifelong bacterial resistance.
Lochan Upadhayay +3 more
wiley +1 more source
Microstructural characterisation and thermal stability of an Mg-Al-Sr alloy prepared by rheo-diecasting [PDF]
, 2007 A commercial Mg-6Al-2Sr (AJ62) alloy has been prepared by a semisolid rheo-diecasting (RDC) process. The microstructure of the RDC alloy exhibits typical semisolid solidification features, i.e., 8.4 vol% primary α-Mg globules (23 μm in diameter), formed ...
Fan, Z, Liu, G, Wang, F, Wang, Y
core
Antiferromagnetic ground state in the MnGa$_4$ intermetallic compound
, 2018 Magnetism of the binary intermetallic compound MnGa$_4$ is re-investigated. Band-structure calculations predict antiferromagnetic behavior in contrast to Pauli paramagnetism reported previously.
Gippius, A. A. +5 more
core +1 more source
A New Family of Ternary Intermetallic Compounds with Dualistic Atomic Ordering – The ZIP Phases
Advanced Materials, EarlyView.The ZIP phases are ternary intermetallic compounds with dualistic atomic ordering, i.e., they exhibit one face‐centered cubic (fcc; space group Fd3¯$\bar 3$m) variant and one hexagonal (space group P63/mmc) variant. The ZIP phases in the Nb‐Si‐Ni system are the Nb3SiNi2 (fcc) and Ni3SiNb2 (hexagonal) ternary IMCs, crystal structure schematics of which ...
Matheus A. Tunes +24 more
wiley +1 more source
AIMS Materials ScienceReactive sintering of Al-Mg powder mixtures containing 5, 10, 15, and 20 wt.% Mg was used to synthesize lightweight composites reinforced with in-situ formed Al3Mg2 and Al12Mg17 intermetallics.
Marek Konieczny
doaj +1 more source
Magnetic States and Electronic Properties of Manganese-Based Intermetallic Compounds Mn2YAl and Mn3Z (Y = V, Cr, Fe, Co, Ni; Z = Al, Ge, Sn, Si, Pt) [PDF]
, 2023 В. В. Марченков +1 more
openalex +1 more source
Spin and Charge Control of Topological End States in Chiral Graphene Nanoribbons on a 2D Ferromagnet
Advanced Materials, EarlyView.Chiral graphene nanoribbons on a ferromagnetic gadolinium‐gold surface alloy display tunable spin and charge states at their termini. Atomic work function variations and exchange fields enabe transitions between singlet, doublet, and triplet configurations.
Leonard Edens +8 more
wiley +1 more source
Effect of the over-ageing treatment on the mechanical properties of AA2024 aluminum alloy. [PDF]
, 2012 The evolution of the hardness of the over-ageing AA2024 alloy scale was followed by measurements of Vickers hardness. The nanoindentation is adapted to the determination of elastoplastic properties (hardness and Young’s modulus) of the matrix and also of
Abrudeanu, Marioara +6 more
core
Fatigue of friction stir welded 2024-T351 aluminium alloy
, 2002 Fatigue failure characteristics of friction stir welds in 13mm gauge 2024-T351 plate have been assessed. Failure occurred from either the weld region (nugget/flow arm) or from the material immediately surrounding the weld.
Booth, D., Sinclair, I.
core +1 more source