Study of Titanium based Composite Coatings for Resistance against Molten Aluminium Soldering on H13 Tool Steel [PDF]
, 2011 The service life of industrial components is limited predominantly by chemical corrosion, mechanical failure or mechanical wear. In the aluminium high pressure die casting industry, liquid aluminium is extremely reactive with the constituents of H13 die ...
Salman, Asma Siddiq
core
Superconductivity of the new intermetallic compound TaPtSi [PDF]
, 2014 A new superconducting intermetallic compound with a chemical formula of TaPtSi was discovered in the Ta-Pt-Si system, and its crystallographic, magnetic, and electric properties were investigated.
Kasahi, A. +6 more
core +1 more source
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
Advanced Engineering Materials, EarlyView.The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source
International Journal of Electrochemical Science, 2015 Electrodeposition of copper-zinc intermetallic compounds (particularly CuZn5) has been carried out onto an AISI 1018 steel substrate from an alkaline non-cyanide solution at room temperature.
J.C. Ballesteros +3 more
doaj +1 more source
The Structure and Stability of High Temperature Intermetallic Phases for Application within Coating Systems [PDF]
, 2009 The reduction of noise and emissions is becoming increasingly important in civil aircraft jet engines as well as requirements for reduced fuel consumption and improved efficiency.
Roberts, Tracey
core
Improvement of the tribological properties of pure Ti by laser cladding intermetallic compound composite coating [PDF]
, 2011 Intermetallic compound composite coating was fabricated on pure Ti substrate by laser cladding. The microstructure and tribological properties of the prepared intermetallic compound coating sliding against AISI-52100 steel ball at different normal loads
J-M Chen, J-R Zhao, C Guo, J-S Zhou
core +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
MetalsThe brittleness of 18-karat purple gold originates from the AuAl2 intermetallic compound. This study investigates the microstructural modification of the AuAl2 intermetallic compound by adding silicon (Si) and cobalt (Co) and by rapid solidification in ...
Adiruj Peerawat +4 more
doaj +1 more source
Effect of Si, Co, Fe contents and cooling condition on the microstructure of Al–Si–Co(–Fe) alloys
Materials Research Express, 2023 In this paper, several Al–Si–Co and Al–Si–Co–Fe alloys were prepared by varying the contents of Si, Co and Fe, solidified via fast and slow–cooling conditions.
Zhenlei Li +4 more
doaj +1 more source
Formation of an intermetallic compound between selenium and copper [PDF]
, 1994 When selenite solutions are determined in the presence of copper using anodic stripping voltammetry (ASV), a new peak appears, which is not associated with copper or selenium.
Mehmet S. Karacan +3 more
core +1 more source