Results 201 to 210 of about 1,603,656 (292)
Materials and Corrosion, EarlyView.Schematic representation of the operando ICP‐OES setup during the electrochemical experiment (left). Resulting plot showing the dissolution of the individual alloy components of AA7075 as a function of applied potential in 10 mM NaCl (right). ABSTRACT This publication deals with the simultaneous acquisition of electrochemical and inductively coupled ...
Claudia Kutzer‐Schulze +2 more
wiley +1 more source
A Review of Research Progress on Ti(C,N)-Based Cermet Binder by Intermetallic Compounds and High-Entropy Alloys. [PDF]
Materials (Basel)Wang L, Bai J, Wang Y, Men Z.
europepmc +1 more source
Corrosion-Free EMF Measurements of Zinc-Based Intermetallic Compounds at Ambient Temperature. [PDF]
Chemphyschem, 2020 Kriegel R, Armbrüster M.
europepmc +1 more source
Materials and Corrosion, EarlyView.Excellent corrosion resistance of commercial Al‐containing materials is shown for exposures to liquid lead (Pb) at 600°C. However, oxide scale failure occurs at 700°C. The formed oxide scales and their failure mechanisms are explored. ABSTRACT Liquid lead (Pb) is an attractive heat transfer fluid for advanced thermal energy storage (TES) systems.
Renate Fetzer +4 more
wiley +1 more source
Analysis of Corrosion and Wall Perforation in the Heat Exchanger Made of AISI 316L Stainless Steel
Materials and Corrosion, EarlyView.Elevated passivation temperature is identified as the dominant factor triggering localized corrosion and subsequent perforation of AISI 316L heat exchanger tubes. Electrochemical and complementary characterization results show that the alloy retains high resistance to general, pitting, and intergranular corrosion, indicating that failure primarily ...
Bojana Radojković +7 more
wiley +1 more source
Materials and Corrosion, EarlyView.The corrosion resistance of heat‐treatable aluminium alloys depends directly on the applied heat treatment. This article discusses the relationship between cooling rate and intergranular corrosion sensitivity. The intergranular corrosion depths were determined by light microscopy of cross‐sections and correlated with both non‐destructive eddy current ...
Hanna Schulz +3 more
wiley +1 more source
First-Principles Study of the Structural, Mechanical, Electronic, and Thermodynamic Properties of AlCu2M (M = Ti, Cr, Zr, Sc, Hf, Mn, Pa, Lu, Pm) Ternary Intermetallic Compounds. [PDF]
Materials (Basel)Guo Y, Jiang B, Zhang X, Li S.
europepmc +1 more source
Development of Calcium‐Based Coatings to Mitigate Vanadate Corrosion
Materials and Corrosion, EarlyView.Ca‐rich coatings can suppress the corrosive attack of molten V2O5 by forming Ca2 V2 O7 and Ca V2 O6. For this, a large Ca‐reservoir is key to mitigate corrosion at 600°C and 700°C. ABSTRACT Vanadate corrosion occurs in devices powered by heavy fuel oil, such as stationary turbines.
Mark Alexander Ulherr +5 more
wiley +1 more source
Interface Control in Additive Manufacturing of Dissimilar Metals Forming Intermetallic Compounds-Fe-Ti as a Model System. [PDF]
Materials (Basel), 2020 Cui D, Mohanta A, Leparoux M.
europepmc +1 more source
Materials and Corrosion, EarlyView.Intergranular corrosion of AISI 304L is analyzed, combining DLEPR test and AE. Slow scan rate polarization reveals time‐shifted and frequency‐dependent acoustic emission in the active region of the DLEPR curve, allowing a separation between passive oxide rupture, intergranular corrosion and pitting. ABSTRACT Intergranular corrosion (IGC) susceptibility
Alexander Kreisch +2 more
wiley +1 more source