Results 51 to 60 of about 7,293 (261)

Ontology‐Aligned Structuring and Reuse of Multimodal Materials Data and Workflows Toward Automatic Reproduction

Advanced Engineering Materials, EarlyView.
Reproduction of stacking fault energy calculations from literature with a semi‐automated large language model‐assisted extraction procedure: extraction of simulation protocol, atomistic structures, computational parameters, and reported results, ontology alignment, knowledge graph construction and, finally, recomputation forvalidation.
Sepideh Baghaee Ravari, Abril Azocar Guzman, Sarath Menon, Stefan Sandfeld, Tilmann Hickel, Markus Stricker   +5 more
wiley   +1 more source

d-magnetism instability in R-Co intermetallic compounds

Journal of Science: Advanced Materials and Devices, 2016
Magnetic phenomena observed in R-Co intermetallic compounds with the d-magnetism instability are reviewed. The magnetic instability in these compounds is intimately related to the special position of the Fermi level in the hybridized 3d-5d (4d) band near
Irina Yu. Gaidukova, Ashot S. Markosyan
doaj   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

First-Principles and PSO-Driven Exploration of Ca-Pt Intermetallics: Stable Phases and Pressure-Driven Transitions

Crystals
In this study, first-principles calculations in conjunction with the particle swarm optimization (PSO) algorithm structure search method were employed to investigate the stable phases of Ca-Pt intermetallic compounds under various pressure conditions ...
Yifei Wang, Dengjie Yan
doaj   +1 more source

The intermetallic compound BaAgBi

Acta Crystallographica Section E Structure Reports Online, 2002
BaAgBi was obtained as a by-product when Ba [rod, Alfa–Aesar (99.99%)], Ag [powder, −100 mesh, Alfa–Aesar (99.999%)], and Bi [powder, −100 mesh, Alfa–Aesar (99.999%)] were loaded into a tantalum tube (Nobel-Met. Ltd, >99.85%, 0.375 in. OD) in a 1:1:2 molar ratio in an Ar-filled glovebox.
Kang, Sung Kwon, Miller, Gordon
openaire   +3 more sources

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source

Compounds with Polar Metallic Bonding

Crystals, 2019
Recently, I witnessed a discussion amongst solid state chemists whether the term polar intermetallic bonding was necessary or dispensable, whether a conceptual discernation of this special class of intermetallic compounds was indicated or spurious [...]
Constantin Hoch
doaj   +1 more source