Results 41 to 50 of about 1,603,656 (292)

Effect of severe plastic deformation on evolution of intermetallic layer and mechanical properties of cold roll bonded Al-Steel bilayer sheets

Journal of Materials Research and Technology, 2020
In this study, evolution of intermetallic layer of the cold roll bonded bilayer of Aluminum-Steel sheets, during severe plastic deformation (SPD) followed by annealing has been investigated.
H. Dehghanpour Baruj, A. Shadkam, M. Kazeminezhad   +2 more
doaj   +1 more source

Internal friction in advanced Fe-Al intermetallics [PDF]

, 2006
We have measured the internal friction and the dynamic modulus of an Fe–38 at.% Al alloy using a forced torsion pendulum working between 10−3 and 10 Hz. The measurements have been carried out as a function of temperature (from room temperature to 1200 K)
Nó, Maria Luisa, Fournier, Dominique, San Juan, Jose, Viguier, Bernard, Lacaze, Jacques   +4 more
core   +1 more source

Low Conductivity Decay of Sn–0.7Cu–0.2Zn Photovoltaic Ribbons for Solar Cell Application

Micromachines, 2019
The present study applied Sn−0.7Cu−0.2Zn alloy solders to a photovoltaic ribbon. Intermetallic compounds of Cu6Sn5 and Ag3Sn formed at the Cu/solder/Ag interfaces of the module after reflow.
Kuan-Jen Chen, Fei-Yi Hung, Truan-Sheng Lui, Lin Hsu   +3 more
doaj   +1 more source

Non-equilibrium solidification of intermetallic compounds in the Ni-Al alloy system [PDF]

, 2007
Ni-Al alloy system exhibits particular solidication behavior due to chemical long-range order of the intermetallic compounds Ni3Al (L12) and NiAl (B2). Using rapid solidication technique their slow solidication kinetics leads to the entrapment of solute
Hartmann, H., Galenko, P. K., Assadi, H., Herlach, D. M., Reutzel, S.   +4 more
core  

Ontology‐Aligned Structuring and Reuse of Multimodal Materials Data and Workflows Toward Automatic Reproduction

Advanced Engineering Materials, EarlyView.
Reproduction of stacking fault energy calculations from literature with a semi‐automated large language model‐assisted extraction procedure: extraction of simulation protocol, atomistic structures, computational parameters, and reported results, ontology alignment, knowledge graph construction and, finally, recomputation forvalidation.
Sepideh Baghaee Ravari, Abril Azocar Guzman, Sarath Menon, Stefan Sandfeld, Tilmann Hickel, Markus Stricker   +5 more
wiley   +1 more source

Effect of inhomogeneous plastic deformation on the interfacial microstructure and properties of titanium/stainless steel

Journal of Materials Research and Technology, 2023
To solve the problem of low interfacial bonding strength caused by the violent reaction of the titanium/stainless steel interface, the corrugated rolling-flat rolling (CFR) process was used to introduce inhomogeneous plastic deformation, and the titanium/
Wenjing Wang, Yingming Tu, Mohan Liu, Xuefeng Liu   +3 more
doaj   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Intermetallic compounds for nitrogen electrochemistry

Green Energy & Environment
Electrochemical nitrogen transformation techniques represent a burgeoning avenue for nitrogen pollutant remediation and synthesizing valuable nitrogenous products from atmospheric nitrogen.
Haohong Wei, Cheng Tang, Yanyun Wang, Yongcheng Feng, Huancong Shi, Mingjin Cui, Huakun Liu, Shixue Dou, Laiquan Li   +8 more
doaj   +1 more source

Intermetallic Compounds

, 2018
Intermetallic compounds are usually brittle with high melting points. Their properties are often found among ceramic and metallic materials. In most cases, their hot corrosion resistance and simultaneously hardness are important.

core   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source