Results 111 to 120 of about 7,293 (261)

Enhanced Mechanical Properties Via Boron‐Induced Multi‐Mechanism Strengthening in (NbTaTi1.5V)100‐xBx Refractory High Entropy Alloys

Advanced Science, EarlyView.
A trace amount of boron is introduced into NbTaTi1.5V RHEA, forming a finegrained BCC+TiO+TiB microstructure. The TiB phase generates numerous dislocations, strengthening the alloy. The alloy exhibits 3610 MPa compressive fracture strength and 1060 HV microhardness, while retaining 14.8% fracture strain.
Da Wu, Bo Li, Yuzhi Shi, Cong Li, Eryong Liu, Xiaohu Hou, Yimin Gao, Tao Wu, Pucun Bai, Chenyu Liang   +9 more
wiley   +1 more source

Chemically Gradient Ordered Nanodomains Enable Large Tensile Ductility in Gigapascal Lightweight Refractory High‐Entropy Alloys

Advanced Science, EarlyView.
A high‐strength lightweight refractory high‐entropy alloy achieves extraordinary ductility owing to the introduction of coherent chemically gradient ordered nanodomains (CGONs). The CGONs not only serve as effective barriers to dislocation motion (strengthening) but also significantly promote dislocation nucleation and multiplication (ductilizing) upon
Wei Zhang, Dingshun Yan, Yong Zhang, Zhiming Li   +3 more
wiley   +1 more source

Investigation of variations of metallurgical and morphological phenomena of interface in the magnetic pulse welding of Al–Cu

Journal of Materials Research and Technology
This study investigates the bonding interface characteristics, formation mechanisms of metallurgical bonds, and intermetallic compounds in Al–Cu joints produced by magnetic pulse welding (MPW) using an E-type coil.
Morteza Sarvari, Amir Abdollah-zadeh, Homam Naffakh-Moosavy   +2 more
doaj   +1 more source

Fabrication of CrSi₂-Containing Master Alloys for Modification of Fe-Containing Intermetallic Compounds in Aluminum Alloys. [PDF]

Materials (Basel), 2022
Sun J, Takahashi A, Higashi K, Yamamoto T, Komarov S.   +4 more
europepmc   +1 more source

Overcoming the Catalytic Bucket Effect in Pt‐based High‐Entropy Nanocages Through Interface Defect and Strain Engineering

Advanced Science, EarlyView.
PtPdNiCuMnAu HENCs exhibit a remarkable half‐wave potential (E1/2) of 0.925 V vs. RHE. The catalyst displays exceptional electrochemical stability, with only a 4 mV negative shift in E1/2 and a mere 5.6% loss in MA after 10, 000 accelerated durability test cycles.
Qian Liu, Haoran Kang, Yiou Liu, Xiaowei Zhang, Xu Chen, Faming Gao   +5 more
wiley   +1 more source

Formation Mechanism of Thicker Intermetallic Compounds in Friction Stir Weld Joints of Dissimilar AA2024/AZ31B Alloys. [PDF]

Materials (Basel), 2022
Tan M, Wu C, Shi L.
europepmc   +1 more source

Extended Anionic Network in Mixed‐Valent Nitridocobaltates(I/II) LnCo2N2 (Ln = La, Pr, Nd)

Advanced Science, EarlyView.
This study presents the high‐pressure synthesis of LnCo2N2 (Ln = La, Pr, Nd) with Co in mixed valent states of +I/+II. The compounds demonstrate the stabilization of a nitridocobaltate with extended anionic Co–N layers where Co is threefold coordinated.
Nina A. M. Prinz, Jonas M. Albrecht, Dominik Werhahn, Simon Steinberg, Clemens Ritter, Simon D. Kloß   +5 more
wiley   +1 more source

A mechanism for the strange metal phase in rare-earth intermetallic compounds. [PDF]

Proc Natl Acad Sci U S A, 2022
Wang J, Chang YY, Chung CH.
europepmc   +1 more source

A Molten Salt Extraction Method for Palladium Recovery via the CaPd2 Intermetallic Compound

Advanced Science, EarlyView.
A designed Ca → CaPd2 → Pd pathway enables acid–free palladium recovery in molten salt. Calcium alloying forms anionic CaPd2, which is selectively oxidized by iodine from CaI2 to yield high–purity metallic Pd. ABSTRACT To address palladium scarcity and the low efficiency of conventional recovery processes, this work presents a molten–salt extraction ...
Jiapeng Zhang, Dengjie Yan, Muwen Chen, Baoqiang Xu, Bin Yang, Bingyi Song, Lingxin Kong   +6 more
wiley   +1 more source

The Growth Behavior for Intermetallic Compounds at the Interface of Aluminum-Steel Weld Joint. [PDF]

Materials (Basel), 2022
Yu X, Huang J, Yang T, Fan D.
europepmc   +1 more source