Results 171 to 180 of about 60,244 (249)
Advanced Engineering Materials, EarlyView.This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani +2 more
wiley +1 more source
Redes de Ingeniería, 2015 En este artículo se presenta el diseño y modelado de un inversor monofásico tipo puente que permite la conexión a la red eléctrica, de paneles fotovoltaicos.
Cesar Leonardo Trujillo Hernandez +2 more
doaj
Sistema fotovoltaico aislado: inversor monofásico
, 2014 Sistema fotoboltaiko batean parte hartuko duen 300W-ko inbertsore baten diseinua deskribatzen da gradu amaierako lan honetan. Inbertsorearen funtzionamendu teorikoren ikasketa garatuko da, honen tipologia desberdinak aurkeztuz. Inbertsorearen atal desberdinak garatzeko beharrezko kalkuluak egingo dira.
openaire +2 more sources
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller +6 more
wiley +1 more source
ASSESSMENT OF ISOMETRIC AND ISOKINETIC ANKLE STRENGTH MEASURES: A PILOT STUDY. [PDF]
Acta Ortop BrasLins C +6 more
europepmc +1 more source
3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs
Advanced Engineering Materials, EarlyView.This work explores 3D‐printed GMR sensors utilizing self‐compliant spring structures and conductive PLA composites. By optimizing arm width, we achieved high piezoresistive (0.34%/mm) and magnetoresistive (0.77%/mT) sensitivities. Demonstrated through Bluetooth‐integrated pressure and magnetic position sensing, these full printed low‐cost, customizable
Josu Fernández Maestu +4 more
wiley +1 more source
Acquired Pes Planovalgus : Current Concepts - "From Adult Acquired Pes Planovalgus to Progressive Collapsing Foot Deformity". [PDF]
Rev Bras Ortop (Sao Paulo)Dressler HB +4 more
europepmc +1 more source
Electrical Conductivities of Conductors, Semiconductors, and Their Mixtures at Elevated Temperatures
Advanced Engineering Materials, EarlyView.This article presents a comprehensive review of temperature‐dependent electrical conductivity data for multiple material classes at elevated temperatures, highlighting a persistent conductivity gap between metals and semiconductors in the range of 102$\left(10\right)^{2}$– 107$\left(10\right)^{7}$ S/m. Metal–ceramic irregular metamaterials are proposed
Valentina Torres Nieto, Marcia A. Cooper
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source