Results 11 to 20 of about 30,440,700 (274)
Shape Memory Properties and Microstructure of New Iron-Based FeNiCoAlTiNb Shape Memory Alloys [PDF]
The shape memory properties and microstructure of Fe41Ni28Co17Al11.5(Ti+Nb)2.5 (at.%) cold-rolled alloys were studied at the first time using the values reported in constant stress thermal cycling experiments in a three-point bending test.
Li-Wei Tseng +4 more
doaj +2 more sources
Development of a new iron-based shape memory alloy
The object of research is the technology for producing iron-based shape memory alloy. One of the most problematic moments in this process is the need to increase the degree of shape recovery while maintaining high mechanical characteristics. It is found that the developed iron-based shape memory alloy has sufficient mechanical properties.
Sundus, A. M. (Ahmed)
openaire +4 more sources
Application of an Iron-Based Shape Memory Alloy for Post-Tensioning Glass Elements
Previous research has evidenced that by adding a ductile reinforcement on the tension side of a glass beam, for instance by adhesive bonding, its post-cracking behaviour and redundancy were improved, while an additional pre-stressing of this ...
Vlad-Alexandru Silvestru +5 more
doaj +4 more sources
Microstructure investigation of new iron-based FeNiCoAlTiNb shape memory alloys
The microstructure of Fe41Ni28Co17Al11.5Ti1.25Nb1.25 (at.%) polycrystalline alloy was investigated for this study. The homogeneous heat treatment condition is 1277 °C for 24 h.
Li Wei Tseng +3 more
doaj +2 more sources
Effect of NbC and TiC precipitation on shape memory in an iron-based alloy
This paper examines the effects of TiC and NbC precipitation and prior cold rolling on the shape memory behaviour of an iron-based alloy. A precipitate-free alloy was used as a reference to investigate the relative contributions of prior-deformation and precipitation on shape memory. Heat treatment of the Nb- and Ti-containing alloys at 700 °C and 800 °
Stanford, Nicole, Dunne, Druce P
openaire +3 more sources
Strengthening of RC beams with iron-based shape memory alloy strips
Low cost Fe-Mn-Si based shape memory alloys (SMAs) can be a cost-effective alternative to the expensive Ni-Ti based shape memory alloys. The application of iron-based shape memory alloy (Fe-SMA) strips for structural strengthening of reinforced concrete (RC) beams is shown in this paper.
Shahverdi, Moslem +2 more
core +4 more sources
Development of Rolling Technology for an Iron-Based Shape-Memory-Alloy [PDF]
Low cost Fe-Mn-Si based shape memory alloys (SMA) have drawn much attention during the last two decades as a cost-effective alternative to the expensive Ni-Ti based SMA. In particular, the alloy Fe-17Mn-5Si-10Cr-4Ni-1(V,C) (mass%), which has been developed at Empa shows very promising properties with regard to potential commercial applications in civil
Leinenbach, Christian +4 more
openaire +1 more source
Iron-Based shape memory alloy for strengthening of 113-Year bridge
Abstract This study focuses on the large-scale application of a Fe-Mn-Si shape memory alloy (Fe-SMA) for strengthening a historic roadway bridge in Petrov nad Desnou (113-years), Czech Republic. To the best of the authors’ knowledge, this is the first application of an iron-based SMA (Fe-SMA) for prestressed strengthening of a bridge.
Vůjtěch, Jakub +3 more
openaire +3 more sources
Active disassembly applied to end of life vehicles [PDF]
This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.Active Disassembly is technology that has been developed to allow assemblies to readily separate for recycling when they are exposed to certain triggering ...
Jones, Nicholas
core +7 more sources
The seismic performance of a concrete column retrofitted with an iron-based shape memory alloy (Fe-SMA) was evaluated under cyclic loading. In addition to structural behavior, internal damage was monitored using an ultrasonic pulse velocity test.
Taemin Lee +4 more
doaj +1 more source

