Results 41 to 50 of about 31,460 (306)
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Thin circular plate uniformaly loaded over a concentric elliptic path and supported on columns
International Journal of Mathematics and Mathematical Sciences, 1986 Within the limitations of the classical thin plate theory expressions are obtained for the small deflections of a thin isotropic circular plate uniformly loaded over a concentric ellipse and supported by four columns at the vertices of a rectangle whose ...
W. A. Bassali
doaj +1 more source
An Experimental High‐Throughput Approach for the Screening of Hard Magnet Materials
Advanced Engineering Materials, EarlyView.An entire workflow for the high‐throughput characterization and analysis of compositionally graded magnetic films is presented. Characterization protocols, data management tools and data analysis approaches are illustrated with test case Sm(Fe, V)12 based films.
William Rigaut +16 more
wiley +1 more source
INFLUENCE OF THE LENGHTS RATIO TO THE STATIC ANSWER IN THE MOVEMENT OF A ROAD DECK [PDF]
Fiabilitate şi Durabilitate, 2017 The article presents a method to obtaining the static response bridge-vehicle system in displacements,and the influence of the lengths ratio of the deck bridge on this response.
Ovidiu GAVRIŞ
doaj
Advanced Engineering Materials, EarlyView.Composite Ti–6Al–4V–epoxy lattice structures are additively manufactured and epoxy infiltrated for cyclic loading. At low lattice volume fractions, hybridization produces synergistic gains in stiffness and energy dissipation. At higher volume fractions, synergy diminishes, although composites still exceed metallic lattices in specific energy ...
Joey Tallon +3 more
wiley +1 more source
Bounds on the effective isotropic moduli of thin elastic composite plates
Archives of Mechanics, 2010 The main aim of this paper is to estimate the effective moduli of an isotropic elastic composite, analyzed within the framework of the Kirchhoff-Love theory of thin plates in bending.
G. Dzierżanowski
doaj +1 more source
, 2014 The APCF/SIF-2014 Congress uniting: Asian-Pacific Conference on Fracture and Strength (APCFS-2014) International Conference on Structural Integrity and Failure (SIF-2014)The scattering of Lamb waves has been adopted for effective detection of different ...
Cazzolato, B. +7 more
core +1 more source
Measured Lamb wave radiation patterns from 011 Mn-PMN-PZT relaxor ferroelectric disks on an isotropic plate [PDF]
, 2018 Three-dimensional laser Doppler vibrometry is used to quantify the modal composition of the guided plate waves generated by relaxor ferroelectric disk actuators of a 011 poled Mn-Pb(Mg1/3Nb2/3)O-lead zirconate titanate (PZT) single crystal and ?100 ...
Moss, S. D. +15 more
core +1 more source
From Shear to Sound: Mechanics–Acoustics Mapping of TPMS Lattices
Advanced Engineering Materials, EarlyView.Triply periodic minimal surface (TPMS) lattices are mapped across mechanical and acoustic performance, revealing that descriptors validated in compression fail under shear. First‐time comparison with trusses included. A transition from porous to resonance‐driven absorption emerges at 25% density.
Lucía Doyle +3 more
wiley +1 more source
Buckling analysis of thick plates using refined trigonometric shear deformation theory
Journal of Materials and Engineering Structures, 2015 In this paper, a refined trigonometric shear deformation plate theory is applied for the buckling analysis of thick isotropic square and rectangular plates.
Sachin Madhavrao Gunjal +3 more
doaj