Results 1 to 10 of about 3,915,807 (126)
Resolving the fundamentals of the J-integral concept by multi-method in situ nanoscale stress-strain mapping [PDF]
Communications MaterialsThe integrity of structural materials is oftentimes defined by their resistance against catastrophic failure through dissipative plastic processes at the crack tip, commonly quantified by the J-integral concept.
Michael Meindlhumer +9 more
doaj +2 more sources
Open Engineering, 2022 This article presents the results of analytical and numerical research focused on the numerical determination of selected fracture mechanics parameters for beams containing a crack in the state of four-point bending with the dominance of a plane strain ...
Graba Marcin
doaj +1 more source
THE ANALYSIS OF CRACK ON COMPOSITE MATERIALS BY USING ENERGY METHOD [PDF]
مجله مدل سازی در مهندسی, 2009 Â A . Fereidoon1,*, F . Yektaye Kia2 Â Â Â 1- Associate Professor, Faculty of Mechanical Engineering, Semnan University, Semnan, Iran. Â 2- M.Sc. Student, Faculty of Mechanical Engineering, Semnan university, Semnan, Iran.
عبدالحسین فریدون +1 more
doaj +1 more source
Brittle failure criteria of CNRB specimen for fracture toughness test
Mechanical Engineering Journal, 2020 This paper proposes a technique to determine the dimensions of a CNRB specimen to be used for plane fracture toughness tests. First, the brittle fracture behavior satisfying the small-scale yielding condition is investigated through an elasto-plastic ...
Manato KANESAKI +4 more
doaj +1 more source
On damage process of ceramic thermal barrier coatings subjected to high-temperature tensile loading
Nihon Kikai Gakkai ronbunshu, 2015 Thermal barrier coatings (TBCs) have been deposited onto the blade surface in a land-based gas turbine according to increase of turbine inlet temperature (TIT).
Masayuki ARAI +2 more
doaj +1 more source
Fracture and Structural Integrity, 2019 In this paper an additional criterion was introduced to evaluate the composite repair systems using the limit load analysis. The plastic collapse pressure of API 5L X65 PSL2 steel pressure vessel structure with crack defect is numerically investigated ...
M. Belhamiani +4 more
doaj +1 more source
Nihon Kikai Gakkai ronbunshu, 2015 In this study, the damage process of Thermal Barrier Coatings (TBC), which were exposed at 1273K for 500hours in advance, under tensile loading was observed continuously, and the influence of exposure temperature on crack initiation strength and ...
Yuto SHIMIZU +2 more
doaj +1 more source
Microscopic observation of creep-fatigue crack propagation in lead-free solder
Nihon Kikai Gakkai ronbunshu, 2015 Creep-fatigue crack propagation tests of lead-free solder were conducted under various loading waveforms. The waveforms adapted in displacement-controlled tests were four triangular waveforms: pp waveform having fast loading-unloading, cc waveform having
Keisuke TANAKA +4 more
doaj +1 more source
Fracture and Structural Integrity, 2019 In this paper, an experimental procedure to evaluate the elastic-plastic J-integral at the tip of a fatigue crack is presented. According to this new approach, the elastic component of the J-integral is derived from Thermoelastic Stress Analysis, while ...
G. Meneghetti, M. Ricotta, G. Pitarresi
doaj +3 more sources
Study on mechanical property and adhesive strength of ice under a low temperature condition
Nihon Kikai Gakkai ronbunshu, 2017 Icing is one of important problems that have to be prevented in jet engine of airplane. If thin ice layer deposited on the surface of blade is detached in fight, the debris is scattered and then impacts to a rear stage blade.
Yusuke YASUDA, Masayuki ARAI
doaj +1 more source