Results 71 to 80 of about 952,902 (195)
International Journal of Energy Research, Volume 2026, Issue 1, 2026.Laser cutting of electrodes for lithium‐ion batteries (LIBs) has been studied to achieve high cut‐edge quality. However, the effects of contaminants generated during laser processing and the influence of cut‐edge quality on battery performance have not been sufficiently clarified.
Dongkyu Park +2 more
wiley +1 more source
Optimization of Cutting Process of Medium Density Fibreboards by the Abrasive Water-Jet
Drvna Industrija, 2011 This paper deals with the process of MDF cutting by the abrasive water-jet (WJC) and shows how is kerf width infl uenced by process parameters. It presents the results of monitoring the kerf width related to technical and technological parameters ...
Štefan Barcík +3 more
doaj
A Novel Multicriteria Decision‐Making Approach for WEDM Parameter Selection Using Fuzzy AHP–ARAS
Journal of Engineering, Volume 2026, Issue 1, 2026.Nickel‐based superalloys, particularly Inconel 718, are renowned for their exceptional mechanical properties, which present significant challenges during machining. These alloys possess remarkable fatigue strength, outstanding resistance to corrosion and creep, high work hardening capacity, and impressive strength.
A. Bhowmik +10 more
wiley +1 more source
Control of Kerf Width in Multi-wire EDM Slicing of Semiconductors with Circular Section
Procedia CIRP, 2018 Abstract Multi-wire EDM slicing method have been developed to overcome problems of conventional multi-wire saw method, and high-efficient and high-accurate slicing could be expected compared with a single-wire EDM technologies. Recently, a group power supplying method was newly proposed to satisfy both processing efficiency and simplification of ...
Yasuhiro Okamoto +4 more
openaire +1 more source
Knee Surgery, Sports Traumatology, Arthroscopy, Volume 33, Issue 12, Page 4291-4302, December 2025.Abstract Purpose Kinematic alignment (KA) total knee arthroplasty (TKA) aligns the femoral component to restore the pre‐arthritic posterior joint line, potentially altering the heights of the medial and lateral trochlear peaks. It remains unclear whether the femoral component should be adjusted to correct deviations in peak height.
Stephen M. Howell +4 more
wiley +1 more source
Experimental Investigation of Kerf Width and Kerf Taper in Fiber Laser Cutting of Aluminium Alloy
International Journal of Innovations in Engineering and Science, 2023 P. P. Kharche, Dr. Vijay H. Patil
openaire +1 more source
Self‐Organization of Redeposited Binder Nanoparticles in Cubic Boron Nitride Materials
Small, Volume 21, Issue 52, December 29, 2025.The article reveals a novel approach to forming micro‐spherical agglomerates through nanosecond laser irradiation, enabling rapid growth of titanium nanoparticles in air. It explores the self‐organisation of redeposited Ti nanoparticles on cubic boron nitride composites, detailing structural and chemical transformations that pave the way for innovative
Manuela Pacella +3 more
wiley +1 more source
Engineering Reports, Volume 7, Issue 11, November 2025.The study finds surrounding rock pressure nonlinearly impacts cutter efficiency (peaking at 8 MPa with 12 kN thrust for 19.46 J m−2), while 200°C rock temperature reduces specific energy to 11.52 J m−2 with 9.51% simulation error, showing proper heating enhances efficiency.
Peng Zhou +5 more
wiley +1 more source
Experimental investigation on low-frequency vibration assisted micro-WEDM of Inconel 718
Engineering Science and Technology, an International Journal, 2017 The micro-wire electric discharge machining (micro-WEDM) has emerged as the popular micromachining processes for fabrication of micro-features. However, the low machining rate and poor surface finish are restricting wide applications of this process ...
Deepak Rajendra Unune, Harlal Singh Mali
doaj +1 more source
Kerf Width Optimization in Wire-Cut Electrical Discharge Machine by using Taguchi Method
Jurnal Teknologi, 2012 Today, in most of wire cut electrical discharge machine (WEDM), the suitable machining parameters are relied based on the data from machine manufacturer and the experience of operators. The situation became more difficult when involving numerous and diverse range of parameters and the lack of experience.
Rizauddin Ramli +2 more
openaire +1 more source