Results 81 to 90 of about 952,902 (195)

Modeling and analysis of micro-WEDM process of titanium alloy (Ti–6Al–4V) using response surface approach

Engineering Science and Technology, an International Journal, 2014
Micro-machining technology is effectively used in modern manufacturing industries. This paper investigates the influence of three different input parameters such as voltage, capacitance and feed rate of micro-wire electrical discharge machining (micro ...
P. Sivaprakasam, P. Hariharan, S. Gowri
doaj   +1 more source

Process parameter optimization of laser beam machining for AISI -P20 mold steel using ANFIS method

Results in Surfaces and Interfaces
AISI P20 mold steel is commonly used for injection molds to produce plastic materials, car accessories, and electronic equipment molds. This study employed a fiber laser beam for precise machining of AISI P20 mold steel. The experimental design, based on
Abdullah Eaysin, Sarower Kabir, Ebru Gunister, Nur Jahan, Amir Hamza, Muhammad Ali Zinnah, Adib Bin Rashid   +6 more
doaj   +1 more source

Optimizing kerf quality in high-speed WEDM of thin woven CFRP composites: a taguchi, WASPAS, and PSO approach

Discover Applied Sciences
The process of machining CFRP composites presents unique challenges, particularly in the context of WEDM. The inherent properties of CFRP composites, such as their low electrical conductivity, anisotropic nature, and heterogeneous composition, require ...
Abeer Eisa, Mohamed AbouHawa, Mohamed Fattouh   +2 more
doaj   +1 more source

Assessment of Kerf Width while Working on Laser Beam Machine

, 2023
Dr. Syed Asghar Husain Rizvi, Prashant Trivedi   +1 more
openaire   +2 more sources

Extremely Thin Metal Foil Blades as Cutting Tools for Hard and Brittle Materials

MATEC Web of Conferences, 2018
The manufacturing costs of semiconductor products such as silicon wafers can be reduced by decreasing the kerf loss. In addition, a decrease in the kerf loss leads to an effective utilization of rare materials, which is environmentally beneficial from ...
Sakamoto Satoshi, Akaoka Sanshiro, Gemma Masaya, Kondo Yasuo, Yamaguchi Kenji, Yamaguchi Mitsugu, Yakou Takao   +6 more
doaj   +1 more source

Laser cutting of FDM-printed PLA/wood composites: experimental investigation and numerical modeling analysis

Scientific Reports
In recent years, laser post-processing has gained considerable attention for enhancing the dimensional accuracy of 3D-printed parts fabricated by fused deposition modeling (FDM).
Mohammad Khoran, Omid Mehrabi
doaj   +1 more source

ANALYSE OF THE KERF VARIATION FOR ABRASIVE WATER JET (AWJ) CUTTING OF STEEL

Nonconventional Technologies Review, 2016
A modern method of cutting materials is the abrasive water jet cutting method. It is a method that is in full ascension regarding the level of usability in production.
Adrian Paul Basarman, Mircea Lobontiu
doaj  

1135 INFLUENCE OF KERF WIDTHS TO AN ASSIST GAS FLOW IN LASER CUTTING

The Proceedings of the International Conference on Jets, Wakes and Separated Flows (ICJWSF), 2013
Toshihide, Hanari, Toshiharu, Muramatsu, Masanori, Yamashita, Jun, Sakakibara   +3 more
openaire   +2 more sources

Surface integrity and kerf quality improvement in laser beam machining of Nimonic C-263 by hybrid TOPSIS-grasshopper optimization approach. [PDF]

Sci Rep
Shastri RK, Mohanty CP, Pati PR, Oyyaravelu R, Giri A.   +4 more
europepmc   +1 more source

Optimization of Laser Cutting Parameters for Enhanced Surface Quality and Reduced Kerf Width in AISI 304 Stainless Steel

Gazi Journal of Engineering Sciences
Engin Nas, S. Uzuner
semanticscholar   +1 more source