Results 61 to 70 of about 79,106 (265)

133-W pulsed fiber amplifier with large-mode-area fiber [PDF]

Optical Engineering, 2006
A master-oscillator fiber power amplifier (MOPA) system with a 4-m-long Yb3+-doped homemade large mode area (LMA) double-clad fiber is reported. The system emits up to 133.8 W of amplified radiation at a wavelength of 1064 nm and a repetition rate of 100 kHz, limited only by the available pump power. Peak power of 300 kW at 20 kHz with a pulse duration
openaire   +1 more source

Low-DMGD, Large-Effective-Area and Low-Bending-Loss 12-LP-Mode Fiber for Mode-Division-Multiplexing

IEEE Photonics Journal, 2019
We report the design of 12-LP-mode (21-spatial-mode) fiber with a low differential mode group delay (DMGD), a large effective area, and a low bending loss that is adapted to a mode-division-multiplexing system over the C+L band.
Huan Zhang, Jian Zhao, Zhiqun Yang, Guanju Peng, Zixiang Di   +4 more
doaj   +1 more source

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Single Trench Fiber-Enabled High-Power Fiber Laser

Photonics
As a novel design of large-mode-area fiber, the single trench fiber (STF) providing high higher-order-mode suppression with a large mode area for the fundamental mode shows potential for high-power and high-brightness applications.
Yi An, Fengchang Li, Huan Yang, Xiao Chen, Liangjin Huang, Zhiping Yan, Min Jiang, Baolai Yang, Peng Wang, Zhiyong Pan, Zongfu Jiang, Pu Zhou   +11 more
doaj   +1 more source

Incorporation of Selenium into Sol–Gel‐Derived Bioactive Glass: Influence on Glass Structure, Bioactivity, and its Selective Cytotoxicity

Advanced Engineering Materials, EarlyView.
Selenium was incorporated into a sol–gel‐derived bioactive glass to enable sustained therapeutic ion release. The selenium‐containing glass preserved bioactivity while selectively inducing cytotoxicity in osteosarcoma cells and maintaining osteoblastic viability.
Breno Rocha Barrioni, Thalita Marcolan Valverde, Talita Martins, Guilherme Mattos Jardim Costa, Alfredo Miranda de Goes, Marcello Rosa Dumont, Eduardo Henrique Martins Nunes, Marivalda de Magalhães Pereira   +7 more
wiley   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Mode-adaptive control of a kilowatt-level large-mode-area fiber laser based on 5×1 photonic lantern

High Power Laser Science and Engineering
This study presents high-power mode-selective operation in a large-mode-area (LMA) fiber laser. A spatial mode-adaptive control system incorporating a 5×1 photonic lantern was employed to facilitate mode conversion between the LP01 and LP11 modes.
Wenguang Liu, Yanyang Hu, Hanwei Zhang, Lianchuang Ding, Pengfei Liu, Baozhu Yan, Jiangbin Zhang, Qiong Zhou, Zongfu Jiang   +8 more
doaj   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source