Results 61 to 70 of about 154,423 (300)

Widely Tunable Pulse Duration 100 mJ Single-Mode MOPA System Based on Yb-Doped Tapered Double-Clad Fiber and Nd:YAG Solid-State Amplifiers

Photonics
We report on a 1064 nm master oscillator power amplifier (MOPA) system based on pulse-modulated laser diode seed sources combined with fiber preamplifiers and a Yb-doped tapered double-clad fiber (T-DCF) amplifier used as an all-fiber master oscillator ...
Mikhail Kozlyakov, Andrey Petrov, Grigoriy Mikhailovskiy   +2 more
doaj   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

51.5 W monolithic single frequency 1.97 $\mathrm {\mu} $m Tm-doped fiber amplifier

High Power Laser Science and Engineering, 2013
We demonstrate a monolithic single frequency Tm-doped fiber amplifier with output power of 51.5 W. A single frequency fiber laser at 1.97 $\mathrm {\mu} $m is amplified by a cascaded master oscillator power amplifier (MOPA) system with all-fiber ...
Xiong Wang, Pu Zhou, Xiaolin Wang, Hu Xiao, Lei Si   +4 more
doaj   +1 more source

Characterization of Accumulated B-Integral of Regenerative Amplifier Based CPA Systems

Crystals, 2020
We report on a new approach to measure the accumulated B-integral in the regenerative and multipass amplifier stages of ultrashort-pulse high-power laser systems by B-integral-induced coupling between delayed test post-pulses and the main pulse.
Stefan Bock, Franziska Marie Herrmann, Thomas Püschel, Uwe Helbig, René Gebhardt, Jakob Johannes Lötfering, Richard Pausch, Karl Zeil, Tim Ziegler, Arie Irman, Thomas Oksenhendler, Akira Kon, Mamiko Nishuishi, Hiromitsu Kiriyama, Kiminori Kondo, Toma Toncian, Ulrich Schramm   +16 more
doaj   +1 more source

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Wideband and flat gain series erbium doped fiber amplifier using hybrid active fiber with backward pumping distribution technique

Results in Physics, 2019
A modern wideband and flat gain erbium-doped fiber amplifier (EDFA) is suggested and accomplished, by employing a recently fabricated hafnia-bismuth-erbium doped fiber (HB-EDF) and zirconia-erbium doped fiber (Zr-EDF) as a hybrid active fiber.
Alabbas A. Al-Azzawi, Aya A. Almukhtar, B.A. Hamida, S. Das, A. Dhar, M.C. Paul, H. Ahmad, S.W. Harun   +7 more
doaj   +1 more source

Evolution of spatial and energy characteristics conically divergent beams in the XeF(С-A) amplifier [PDF]

, 2002
Evolution of spatial and energy characteristics start pulse with energy of 0.8 mJ in duration of 2 ps in the XeF(С-A) amplifier of THL-100 laser system have been studied experimentally and by numerical simulation.
Ivanov, Nikolai, Losev, Valery Fedorovich, Panchenko, Yurii, Yastremskii, Arcadii   +3 more
core   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Electrical Conductivities of Conductors, Semiconductors, and Their Mixtures at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This article presents a comprehensive review of temperature‐dependent electrical conductivity data for multiple material classes at elevated temperatures, highlighting a persistent conductivity gap between metals and semiconductors in the range of 102$\left(10\right)^{2}$– 107$\left(10\right)^{7}$ S/m. Metal–ceramic irregular metamaterials are proposed
Valentina Torres Nieto, Marcia A. Cooper
wiley   +1 more source