Results 11 to 20 of about 8,497 (257)
Local Shielding Gas Supply in Remote Laser Beam Welding
Journal of Manufacturing and Materials Processing, 2021 The use of shielding gases in laser beam welding is of particular interest for materials interacting with ambient oxygen, e.g., copper, titanium or high-alloy steels. These materials are often processed by remote laser beam welding where short welds (e.g.
Klaus Schricker +2 more
doaj +1 more source
Melt Pool and Keyhole Behavior Analysis for Deep Penetration Laser Welding [PDF]
, 2010 One usually defines the main characteristic of the welding performances of a given laser system by its “penetration curve” that corresponds to the welding depth as a function of the welding speed Vw for a given set of operating parameters.
R Fabbro, Fabbro, R, FABBRO, Rémy
core +1 more source
Welding with the Laser Beam in Vacuum [PDF]
Laser Technik Journal, 2015 AbstractIn the vehicle industry, beam welding methods are successfully applied for the joining of high‐quality parts. Here, the focus is mainly put on drive section components. Especially in component manufacturing of couplings, toothed wheel — shaft joints and drive shafts, electron beam welding using small vacuum cycle chambers is applied.
Uwe Reisgen +3 more
openaire +1 more source
Analysis of hybrid Nd:Yag laser-MAG arc welding processes. [PDF]
, 2011 In the hybrid laser-arc welding process, a laser beam and an electric arc are coupled in order to combine the advantages of both processes: high welding speed, low thermal load and high depth penetration thanks to the laser; less demanding on joint ...
F. Coste +9 more
core +1 more source
Finite element simulation of magnesium alloys laser beam welding [PDF]
, 2010 The authors are grateful to FONDERIE MESSIER (HONSEL group) that provided the as-cast magnesium alloy workpieces. The authors would like also to acknowledge the technical support of Dr.
BESSROUR, Jamel +4 more
core +1 more source
Research on the Microstructure of Laser Beam Welded Sc-Modified AA2519-F Extrusion [PDF]
Archives of Metallurgy and Materials, 2022 In this paper, the microstructure of laser beam welded Sc-modified AA2519-F has been taken under investigation. The welded joint has been produced using Fanuc 710i industrial robot equipped with YLS-6000 6 kW laser beam source.
R. Kosturek +3 more
doaj +1 more source
Direct keyhole laser welding of aluminum alloy AA5754 to titanium alloy Ti6Al4V [PDF]
, 2014 The tensile strength of direct AA5754/Ti6Al4V joints performed by high speed Yb:YAG laser welding is found to be determined by morphology and phase content of dissimilar interface formed between contacting Al-rich and Ti-rich melted zones. Three types of
CICALA, E +6 more
core +1 more source
The influence of position in overlap joints of Mg and Al alloys on microstructure and hardness of laser welds [PDF]
, 2013 Structure and properties of laser beam welding zone of dissimilar materials, AZ31 magnesium alloy and A5754 Aluminum alloy, are investigated. The microstructure and quality of the Mg/Al weld were studied by metallography, microhardness and optical ...
BANNOUR, Sana +11 more
core +1 more source
Metals, 2019 In order to meet the requirements of alignment capability, gap tolerance and welding track control, dual-beam laser welding has been put forward to weld tailored blanks with different thicknesses.
Xinge Zhang +4 more
doaj +1 more source
Possible explanations for different surface quality in laser cutting with 1 micron and 10 microns beams [PDF]
, 2012 In laser cutting of thick steel sheets, quality difference is observed between cut surfaces obtained with 1 micron and 10 micron laser beams. This paper investigates physical mechanisms for this interesting and important problem of the wavelength ...
Remy Fabbro +3 more
core +1 more source