Results 61 to 70 of about 123,509 (254)
SLS Fabrication of Highly Porous Model Including Fine Flow Channel Network Aiming at Regeneration of Highly Metabolic Organs [PDF]
, 2006 Fabrication of very porous scaffold for regeneration of highly metabolic organs is reported. Polycaprolactone (PCL) powder was mixed with fine salt grains as filler and SLS processed to develop a model including fine flow channel network.
Huang, Hongyun +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Selective laser melting of thermal pre-treated metal oxide doped aluminum oxide granules
Open Ceramics, 2020 The influence of powder bed density on the final density and microstructure of aluminum oxide parts manufactured by direct selective laser melting has been studied.
Stefan Pfeiffer +9 more
doaj +1 more source
A Study of Overripe Seed Byproducts from Sun-Dried Grapes by Dispersive Raman Spectroscopy
Foods, 2021 Overripe seeds from sun-dried grapes submitted to postharvest dehydration constitute a scarcely investigated class of vinification byproduct with limited reports on their phenolic composition and industrial applications. In this study, Raman spectroscopy
Francisco J. Rivero +7 more
doaj +1 more source
Textural evolution and phase transformation in titania membranes: Part 2. - Supported membranes [PDF]
, 1993 Nanostructural evolution and phase transformation in supported and unsupported titania membranes have been studied using Raman spectroscopy, X-ray diffraction (XRD) and field-emission scanning electron microscopy (FE-SEM).
Burggraaf, Anthonie J. +4 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Dry eye associated with laser in situ keratomileusis: Mechanical microkeratome versus femtosecond laser [PDF]
Journal of Cataract and Refractive Surgery, 2009 To compare the incidence of laser in situ keratomileusis (LASIK)-associated dry eye and the need for postoperative cyclosporine A treatment after flap creation with a femtosecond laser and a mechanical microkeratome.Cole Eye Institute, Cleveland, Ohio, USA.Eyes were randomized to flap creation with an IntraLase femtosecond laser (30 or 60 kHz) or a ...
Marcella Q, Salomão +2 more
openaire +2 more sources
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Journal of Biomedical Photonics & Engineering, 2016 A craquelure structure of protein film as indicator of macromolecule state is discussing. Craquelure is a network of fine cracks or crackles on the surface of a painting, caused chiefly by shrinkage of paint film or varnish.
Alexander N. Malov +2 more
doaj +1 more source
Experimental analysis for the effect of dynamic capillarity on stress transformation in porous silicon [PDF]
, 2016 The evolution of real-time stress in porous silicon(PS) during drying is investigated using micro-Raman spectroscopy. The results show that the PS sample underwent non-negligible stress when immersed in liquid and suffered a stress impulsion during ...
Kang, Yi-Lan +4 more
core +1 more source